YSI_Prog_E.pdf - 第50页

1-15 1  asic operation 1.5.3 "Output" screen T his screen displays the c ycle time for inspected boards for each inspection. [Auto] – [Output] screen 24115-P6-00 Item/button name Units Description T otal Inspe…

1-14

asic operation

1.5.2 "Whole" screen

This screen displays the inspection state in real-time, such as the number of boards that have been inspected.

When the inspection program is changed, information related to that inspection program will be cleared.

The displayed items can be changed by pressing the [Display Change] button on the right side of each item.

[Auto] – [Whole] screen

[Display Change] button

NG information

24114-P6-00

Item/button name

Units Description

Display Change Changes the displayed item.

Inspection Count Sheet

Shows the number of boards inspected after the current inspection program is

selected.

Boards for which inspection is stopped before it is completed will not be counted.

Total Count Sheet

Shows the total number of boards inspected after the inspection machine

application software is started.

Cycle Time

Sec/Sheet This is the average inspection time per board.

Sec/Step This is the average inspection time per step.

Sec/Parts This is the average inspection time per part.

Over Judge Rate % OK CONT count / number of inspected steps × 100 (%)

First-Pass Rate %

This is the number of OK boards divided by the number of inspected boards and

then multiplied by 100 (%).

NG Rate %

Number of defective boards / number of inspected boards × 100 (%). This is

counted after the current inspection program is selected

Parts NG Rate %

NG count for each Ref / total Ref count (number of parts) × 100 (%). This is

counted after the current inspection program is selected.

Total NG Rate %

Total number of defective steps / total number of inspected steps × 100 (%). This

is counted after the inspection machine application software is started.

NG Board Count Sheet

Displays the number of NG boards after changing to the inspection program

currently being used to perform inspection.

Total NG Board Count Sheet

Displays the total number of NG boards since the inspection machine application

was started.

First-Pass Count Sheet

Displays the number of OK boards after changing to the inspection program

currently being used to perform inspection.

NG Count Step

Displays the number of NG steps after changing to the inspection program

currently being used to perform inspection.

Total NG Count Step

Displays the total number of NG steps since the inspection machine application

was started.

Operating Rate %/lot

Average inspection time × (number of inspected boards) / machine's cumulative

inspection time

Working Rate %/lot

Average inspection time × (number of inspected boards) / (machine's cumulative

inspection time – board wait time – board unloading wait time)

1-15

asic operation

1.5.3 "Output" screen

This screen displays the cycle time for inspected boards for each inspection.

[Auto] – [Output] screen

24115-P6-00

Item/button name

Units Description

Total Inspection Sec

This is the time from the start of board inspection until the end of board

inspection.

Carry-in Sec

This is the time from the point the board is detected by the sensor at the

conveyor entrance board until board clamping is complete.

Carry-out Sec

This is the time from the point board unclamping is started until the board

passes the sensor at the conveyor exit.

InspectionWaitTime Sec

This is the length of time spent waiting for the judgment from the Repair

Judgment Station or secondary judgment.

Fiducial Recognition Sec

This is the time from the start of board fiducial recognition until the end of board

fiducial recognition. This also includes recognition retry time.

Bad Mark Recognition Sec

This is the time from the start of bad mark recognition until the end of bad mark

recognition. This also includes recognition retry time.

Code Recognition Sec This is the length of time spent performing a code scan.

Optical Inspection Sec This is the board optical inspection time.

Laser Inspection Sec

This is displayed if the machine is equipped with a laser unit.

This is the length of time spent performing laser inspection.

Marking Sec

This is displayed if the machine is equipped with a marking unit.

This is the length of time spent performing marking.

1-16

asic operation

1.5.4 "Bad Mark" screen

This screen allows you to display the bad mark recognition results for each inspection. Recognition results can

be checked by selecting the bad mark type from a drop-down list.

[Auto] – [Bad Mark] screen

Bad mark type

Recognition results

24116-P6-00

1.5.5 "Judge" screen

By enabling the "Second Judge" function in the machine settings, the (Judge) tab is added. This screen displays

board NG results the moment inspection is complete, or after board unloading. Select OK or NG for NG results

displayed in the NG judgment list. Inspection of the next board is performed while performing OK/NG judg-

ment, and therefore inspection of the next board will not be complete until judgment of all NG items is

complete.

TIP

The timing at which results are displayed in the "Judge" screen can be set in "Second Judge Setting"

→

"Judgment

timing" in the machine settings.

[Auto] – [Judge] screen

Displays the inspection result.

Inspection image

OK image

24117-P6-00