00197182-04_AI_Prepare_Kit_SX12_de_en.pdf - 第58页

3 Fitting the Prepare Kit 3.2 Preparing the Trailing Cable Interface Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 Prepare Kit 04/2017 58 3.2 Preparing the Trailing Cable Interface Parts, equipment and tools ●…

Assembly Instructions / Montageanleitung SIPLACE SX1/SX2

Prepare Kit 04/2017

3 Fitting the Prepare Kit

3.1 Preparations at the Machine

3 Fitting the Prepare Kit

3.1 Preparations at the Machine

► Switch off the machine, disconnect it from the power supply and secure it to prevent

unauthorized reactivation. Observe the instructions in section 1.2 "Preparatory Work..." [}48].

► Remove the changeover table from location 2.

Fig.6: Removing the covers

1. Side cover

2. Trailing cable cover

3. Cover on infrastructure box

► Remove the side cover(1) and the trailing cable

cover(2) from the left side of the location.

► Remove the inner cover on the infrastructure box

(3).

3 Fitting the Prepare Kit

3.2 Preparing the Trailing Cable Interface

Assembly Instructions / Montageanleitung SIPLACE SX1/SX2

Prepare Kit 04/2017

3.2 Preparing the Trailing Cable Interface

Parts, equipment and tools

●

Support for trailing cable interface [03068747-xx]

●

Vision hotlink adapter [03050555-xx]

●

Trailing cable interface [03064127-xx]

●

2x ground cable 0.5 m [03055213-xx] from cable set for gantry 2 [03052290-xx]

●

C-parts trailing cable interface support [03094645-xx]

– 10x socket-head screws M3x6 [03042541-xx]

– 2x lens head screws M4x6 [03046903-xx]

– 1x socket-head screws M5x8 [03042559-xx]

– 1x serrated lock washer 5-FSt [03047704-xx]

Installation

The support for the trailing cable interface and the hotlink adapter should be prepared with the

spacer bolts at the top and bottom and with a ground screw.

► First fit the trailing cable interface support with the hotlink adapter, by fixing it from below to

the bracket (4x M3x6 mm socket-head screws).

► Now fit the trailing cable interface from above, onto the support.

(6x M3x6 mm socket-head screws)

Fig.7: Trailing cable interface

1. Jumper for trailing cable interface

2. Ground screw for trailing cable interface

► Fix the ground cable 0.5 m to the support, using

the existing ground screw.

► Fix the ground cable 0.5 m directly to the trailing

cable interface, using the socket-head screw

M5x8 mm and the serrated lock washer 5-FSt.

► Set the jumper as shown in the image.

Fig.8: Trailing cable interface with support

1. Trailing cable interface support

2. Hotlink adapter

3. Trailing cable interface

4. Ground screw for trailing cable interface support

► Attach the pre-fitted trailing cable interface sup-

port, by screwing it with the lens head screws

(M4x6 mm) into the relevant pre-drilled holes

above the infrastructure box.

► Both ground cables are attached to the earthing

panel on the machine. (spare screws and contact

discs can be found on the earthing panel)

Assembly Instructions / Montageanleitung SIPLACE SX1/SX2

Prepare Kit 04/2017

3 Fitting the Prepare Kit

3.3 Preparing and Fitting the GCU

Parts, equipment and tools

●

GCU carrier [03065813-xx]

– 2x hexagonal nuts M4 [03008166-xx]

– Ground M5 [03050528-xx]

– 3x socket-head screw M4x8 mm [03042551-xx]

●

Bracket assembly [03066100-xx]

●

Positioning control unit for gantry axes GCU [03052200-xx]

●

C-parts GCU carrier [03094644-xx]

– 2x hexagonal nuts M4 [03008166-xx]

– 5x socket-head screw M4x8 mm [03042551-xx]

– 2x serrated lock washer 4-FSt [03047857-xx]

– 1x contact disc 4 FSt [03047654-xx]

– 5x washers 4.3mm [00316894-xx]

Installation

► Check the jumper setting on the GCU. This must be as follows for the GCU 3:

Jumper Position

1 Left (OFF)

2 Right (ON)

3 Right (ON)

4 Left (OFF)