00197043-04_VD_706_1_SP2_705_05_SP2_DE_EN.pdf - 第39页
Station S oftware 70 6. 1 SP 2 /705.05 SP 2 / Vers ion De scription Ausgabe 07/2013 E dition 39 6.17 Tap e Secur it y Flag in X - Feeder An X - f eeder can be operated i n man y dif ferent ways in an enviro nment with ou…
Station Software 706.1 SP2/705.05 SP2 / Version Description Ausgabe 07/2013 Edition
38
6.16 PCB Barcode Detection with Molex Traceability Pad
Compatible mode: Complete
If the barcode is not contained on the board, it may be put onto the board with help of the Molex
Traceability Pad (Molex item no.: [91658-0020]).
The Traceability is packaged in tape reels and can be placed in the first placement area of the first
machine in the line, if it is defined as a component.
Procedure in SIPLACE Pro
The barcode fiducial and the placement position of the Traceability-Pad have to be defined in the
same panel. Furthermore, the name of the barcode fiducial has to begin with the character string
FOC_Pos, in which Pos is the name of the placement position.
Example
If the placement position name is Pos_23, the name of the appropriate barcode fiducial has to
be FOC_Pos_23 or FOC_Pos_23_xyz. So, the station software will not read the FOC_Pos_23
barcode fiducial until the Pos_23 Traceability Pad has been placed.
The barcode will then be treated as if it was already read when the board entered the line. The
Whispering down the Line function is supported.
The Traceability Pad should be placed / read in the placement area 1 of the first placement
machine. Only in this case it is warranted that the Traceability information can be correctly saved
for all stations in the line.
NOTICE
Component Height
Barcodes can only be reliably measured by SIPLACE Vision if the component height
(without board warpage) at the position of the Traceability-Pad is < 1,5mm.
The function can also be used to put a component high-precisionly on another component (chip
stacking): for this, the lower component has to be provided with a fiducial that is defined as local
component fiducial, with the nomenclature FOC_BeName for the fiducial name in SIPLACE Pro. By
this name, the software detects that this fiducial shall not be measured until the component has
been placed. The upper component will then be placed relatively to the fiducial.
Station Software 706.1 SP2/705.05 SP2 / Version Description Ausgabe 07/2013 Edition
39
6.17 Tape Security Flag in X-Feeder
An X-feeder can be operated in many different ways in an environment without setup verification.
Therefore, a tape might be exchanged in an X-feeder without notifying SIPLACE Setup Center
about it.
A tape security flag is set in the embedded software of the X-feeder to check for changes on a tape
in the feeder. The tape will be accordingly displayed as "secure" or "insecure" on the GUI of the
station software.
The security flag is set to the "secure" value in the following cases:
– A packaging unit is assigned and the foil is not torn.
– A packaging unit is assigned and a foil torn has been repaired.
The security flag is set to the "insecure" value in the following cases:
– Foil torn
– Foil removal error
– Foil jam
If a feeder is positioned at the station, the security flag is read by the station software and
transferred to SIPLACE Setup Center. SIPLACE Setup Center evaluates the security flag state. If
the "unsecure" value applies, the appropriate packaging unit is torn down and the station is notified
that the track is empty. The corresponding tape will then be displayed as "insecure" on the GUI of
the station software.
6.18 Improved Behavior at Conveyor Problems
Until now, the entire station and not only the concerned input belt was locked at some conveyor
problems. The displayed setup and other data of the current job were reset and thus, it was not
possible to perform a setup verification.
Examples
– The external MES system locks the station during a product change or a change over. The first
board of the next job has already passed the printer while the first station still assembles the
last board of the preceding job. By locking the station, the external system ensures that the
new board does not enter the station too soon.
– During production, an external system detects a problem, e.g. too low pick-up reliability. The
input belt and the station get locked. After the station has been locked it cannot be operated,
e.g. to solve the problem with the concerned component shape, without performing a reboot.
As of this station software version, the concerned input belt will be locked only and correspondingly
displayed by an icon on the GUI. All other station functions can be performed.
Station Software 706.1 SP2/705.05 SP2 / Version Description Ausgabe 07/2013 Edition
40
6.19 Requesting Shutdown Reason on the GUI
If the machine reboots unexpectedly, an error event is generated during shutdown. However, with
this event it cannot be detected if the shutdown was scheduled (e.g. for maintenance) or
unscheduled caused by a software or hardware problem.
In order to find out the shutdown reason, a request can be activated under Settings – GUI
settings as of this station software version.
Figure 5-20: Requesting machine shutdown cause
If the Request reason on shutting down machine option is activated, the following dialog is
displayed after the Shut Down button has been clicked.