00197043-04_VD_706_1_SP2_705_05_SP2_DE_EN.pdf - 第52页

Station S oftware 70 6. 1 SP 2 /705.05 SP 2 / Vers ion De scription Ausgabe 07/2013 E dition 52 Dip module L DU_X – The num ber of LDU _X modules p er head is l imited to one. – The num ber of LDU _X modules p er locatio…

Station Software 706.1 SP2/705.05 SP2 / Version Description Ausgabe 07/2013 Edition

CPP placement head

– Restrictions for the X2, X3, X4, X4i and SX4 placement machines can be found in the

correspondent User Guides to the X-series and in the Version Description to SIPLACE Pro.

– Not vacuum pump compatible.

– Not supported on DX series placement machines.

Reduced air consumption with vacuum pump

No support for CPP placement heads and Twin Head.

VHF P&P head

Supported on the SX1/SX2 V2 placement machine only.

Automatic tray feeding

The function is not supported on the X4i, SX4 and DX4 placement machines.

Quad Lane conveyor

– Quad Lane conveyor is not supported on the X2, X3, SX1/SX2, DX1/DX2 and DX4 placement

machines.

– A Quad Lane job from SIPLACE Pro will always download one recipe for both sub-lanes. It is

not possible downloading one recipe to sub-lane xL and another recipe to sub-lane xR.

– If a single board is downloaded in Quad Lane transport mode, it has to be produced on the

outer sub-lane of the lane pairs, i.e. on 2L or 1R.

– X4 and X4i placement machines: The outer side panels of the sub lanes 2L and 1R are set to

21 inch in the outer position. However, if the placement machines are not exactly in line to each

other, boards might get stuck on handing them over. Therefore the outer side panels can be

manually extended to an over-width of 540 mm. In SIPLACE Pro the maximum width remains

by 535mm.

– Barcode scanner is not supported.

– Due to the reachability of the board camera, asynchronous operation mode with maximum

width is not possible on the X4i placement machine (instead of that, operation in I-Placement

mode).

– Depending on board geometry and placements there might be increased interference with the

gantries in I-Placement mode.

– SIPLACE Traceability and TraceHost are not supported.

– 3rd party traceability systems are only supported on OIS SIS basis.

– The line can only be operated in Quad Lane transport mode and cannot be combined with

single or dual conveyor machines.

Station Software 706.1 SP2/705.05 SP2 / Version Description Ausgabe 07/2013 Edition

Dip module LDU_X

– The number of LDU_X modules per head is limited to one.

– The number of LDU_X modules per location is limited to one.

– Parameterization in the component shape is not transferred to the LDU_X module. The

parameters have to be additionally set at the LDU_X module.

– Reduced LDU_X performance, as maximum 2 A can be provided for each feeder. Therefore

the drives of the LDU_X module cannot reach the maximum possible acceleration.

– LDU_X modules cannot be placed on any track of the X-table because of restrictions

concerning the accessibility with the twin head. The range of usable tracks for setting up

LDU_X modules is limited in SIPLACE Pro.

– LDU_X module and manual tray cannot be placed together on one table on the machine types

X2, X3, X4, X4i and SX4.

– The improvement does not consider the time needed for dipping.

– The eSW of the LDU_X module can only be updated via notebook and serial interface.

– Maximum component dimension: 45 x 45 mm. For TwinHead: squeegee cycle between the two

dipping processes, if the components on both head segments have to be dipped.

– Setup verification is not supported with the LDU-X module.

– Reachability of the LDU_X module in the X-, SX- and DX-series:

X2: Location 1 and 3 39.5 mm

Location 2 and 4 54 mm

X3: Location 1 22.5 mm

Location 3 39.5 mm

Location 2 and 4 54 mm

X4: Location 1 and 3 C&P20/CPP, 38 mm

Location 2 und 4 no restriction

X4i: All Locations 38 mm of 75 mm

SX1/2 and DX1/2:

Location 1 or 2 inner position: no restriction

outer position: half of the dipping area

SX4 All Locations 38 mm of 75 mm

– Dipping with the C&P20A placement head is only possible with LDU_X as of function version 3.

Station Software 706.1 SP2/705.05 SP2 / Version Description Ausgabe 07/2013 Edition

Fast head exchange

– The function only supports the C&P20A and CPP placement heads.

– Stationary cameras will always be calibrated.

– A placement head should always be replaced by a placement head of the same type. If a

placement head is replaced by another head type, the fast exchange time is not granted, as

configuration changes, setup change and hardware exchange will follow.

– A manual head exchange is not detected (e.g. if a placement head is manually disassembled

and identically reassembled during maintenance).

Virtual PCB stack

– The boards will only be placed if the corresponding "PCB Detection Inkspots" is detected.

– No plausibility check is performed. I.e., if both inkspots are detected by mistake, both board

contents will be placed. If neither of the two inkspots is detected, no placement will be

performed.

Rotational angle compensation for short, wide boards

After the station software has been shut down, the start offset is not available anymore.

WPC5 / WPC 6

– Non Stop operation is not supported.

– When the station software is booted it is not detected whether a WPC is connected, as the

WPC has a power supply of its own. Therefore, a reference run can only be prevented by

pressing the emergency stop button.

– Components up to a height of 30mm can be placed with a force of 70N with the WPC5 as of

serial number 1485 and the WPC6 as of serial number C1486 only.

– Due to the refill module, components > 25mm cannot be positioned on the levels 1 – 3 and

27 – 28 on the WPC6. The levels 4 – 28 will be set up automatically by the SIPLACE Pro

Optimizer. The levels 1 – 3 have to be blocked manually by the operator.

CPP/Twin Head/VHF P&P or C&P12/Twin Head/VHF P&P placement heads and high

components in asynchronous dual lane transport mode

Due to the differing "free height" of the placement heads when combining the placement head

types in the processing area, already placed components might be damaged in the following cases:

– During auto recovery, when the board to be recovered is already placed with high components.

– By going to service position.

– During a manually activated refererence run.

– During manual operations, teaching and inspection of placed components with the board

camera. In these cases also components in the opposing trays (WPC/MTC) might be

damaged.

– By using the Long board option.