00197043-04_VD_706_1_SP2_705_05_SP2_DE_EN.pdf - 第59页

Station S oftware 70 6. 1 SP 2 /705.05 SP 2 / Vers ion De scription Ausgabe 07/2013 E dition 59 Fine adju stment of the pitch at th e feeder For f eeder types < 12mm , the current pitch in the feeder has to be set to …

100%1 / 144
Station Software 706.1 SP2/705.05 SP2 / Version Description Ausgabe 07/2013 Edition
58
Counter for operating hours
– If the placement machine is switched off abruptly or by a direct "shutdown" of the station
software console, the current value does not get stored in the EPROM on the I/O module. In
such cases the difference to the latest storage time gets lost (maximum 5 minutes deviation).
– The counter for operating hours gets lost if two or more of the components I/O module, GCU or
station computer are exchanged.
Automatic recognition of the nozzle ID
– Twin heads are not supported.
– The scanned nozzle data gets lost at a machine reboot.
Flexible management of activity level rights
– No message is displayed that a new activity level is active.
– The rights can solely be changed via mouse / trackball (right-click). A change via touchscreen
is not possible.
X4i S placement machine
– The traveling range in X direction is limited for the gantries 2 and 4 on the X4Si placement
machine.
– If a pin picker is installed on the X4i S placement machine, the maximum board length is
410mm.
X3 S and X4 S placement machines
If a pin picker is installed on the X3 S and X4 S placement machines, the maximum board length is
410mm.
TrayStak Feeder AX
– The feeder is only supported on the X4i S placement machine and can be positioned on the
locations 2 and 3 only.
– Only one Dip module LDU-X can be installed beside the feeder.
– If 2 TrayStak Feeder AX are installed together with an LDU-X, the table has to be manually
selected in the Auto Configuration.
– No nozzle changer support.
– Stationary camera cannot be used.
– CPP placement head supported only.
– Feeder and placement heads are neither controlled in SIPLACE Pro nor in the station software.
– Due to the hardware, the sequence oft he components (chain) cannot be warranted. Therefore,
setup verification with SIPLACE Setup Center cannot be performed.
– After the machine has been rebooted or the feeder has been locked / unlocked, the feeder has
to be manually activated with the buttons on the feeder each time.
– If the feeder is used without a reject conveyor, this may result in incomplete head cycles what
causes a reduced placement performance.
– If there is no space to put back the component, it will be rejected.
Station Software 706.1 SP2/705.05 SP2 / Version Description Ausgabe 07/2013 Edition
59
Fine adjustment of the pitch at the feeder
For feeder types < 12mm, the current pitch in the feeder has to be set to > 4mm to achieve the
same functionality as on the operator panel of the feeder and to avoid incorrect settings for smaller
pitches.
Fault-tolerant operation of the Twin Head
– If Segment 1 has been deactivated or removed from the configuration, e.g. some single
placement positions might not be reachable because of the limited traveling range of Segment
2. The machine stops with a corresponding error message and the board cannot be finished.
No plausibility check will be performed in advance for a defined job or a board that enters the
machine.
– Head calibration is not possible, if Segment 1 is deactivated or has been removed from the
configuration. If this is necessary, the functioning segment has to be installed on the position of
Segment 1.
– No CAN communication with a segment that has been removed from the configuration.
– No control of the Z-security for a segment that has been removed from the configuration.
– A segment that has been removed from the configuration will not be actively secured, but will
generally be hold by the cylinder.The segment is held high enough, so that it will not come in
touch with placed components. If necessary, the nozzle has to be manually removed.
– If a long/wide component is placed by the active segment, no check will be performed whether
a component is wiped off from the segment that has been removed from the configuration.
PCB barcode detection with Molex Traceability Pad
– Barcode-controlled production is not supported.
– Traceability is not possible until the barcode has been successfully read. Therefore, the
Traceability Pad should be placed / read in placement area 1 of the first placement machine in
the line. Only in this case, it is warranted that the Traceability information can be correctly
saved for all stations in the line.
– Barcodes can only be reliably measured by SIPLACE Vision if the component height (without
board warpage) at the position of the Traceability-Pad is < 1,5mm.
– When the placement position is taught, the barcode / fiducial position will not be moved
correspondingly.
Station Software 706.1 SP2/705.05 SP2 / Version Description Ausgabe 07/2013 Edition
60
10 Corrected Errors
10.1 706.1 SP2 Station Software
Station software version 706.1 SP2 contains all the error corrections of the previous versions
701.xx – 706.1 SP1. Additionally, the following errors have been corrected in this version:
Error no. Error description
D1-74832811
Height control errors frequently occured when the trays were returned into the
tower.
D1-78661201 The MTC did not consider the acceleration reduction.
D1-79243301 Too long time for downloading a new recipe and setup to the station.
D1-80541901
D16837-1398
This error occurred sporadically when the machine was started:
Head configuration not supported for this machine. Can't
initialize machine hardware
.
D1-81048513
D1-85016987
The "Name" column displaying the placement reference position was missing
in the 706 station software.
D1-82180701
The nozzle was out of center in front of the component camera after a feeder
change and the track was deactivated.
D1-83201901 The machine stopped the production after not having recognized an ink spot.
D1-83344201 The placement position could not be taught.
D1-84180931 Misleading error message for measurement errors during calibration.
D1-84221817 The MTC reference run failed on an X3 S placement machine.
D1-84355807 The cutting unit did not work if only X-feeders 56-88mm were set up.
D1-84734801
D1-86050901
D1-86095301
D16775-4658
After sending a new product the feeder position recognition sporadically failed.
D1-84955201
eSW: the board was not transported to the output conveyor after the conveyor
width had been adjusted
D1-85017141 Sporadically, there were some question marks in the PCB conveyor view.
D1-85076201
The "Feed forward" function did not work when the pickup position was
checked.
D1-85401001
The machine displayed error message 30464 Current of servo
amplifier or motor exceeds threshold
.
D1-85401043
eSW: error message 40006 Board cannot reach target position
although the board was over the sensor.