User-Manual-NeoDen9-PNP-machine.pdf - 第18页

18 Zhejiang Neoden T echnol ogy Co., Ltd It is m ainly used for a single PCB board and m ultiple id entical PCB b oards co nsistent of the whole board (Notic e: coordin ate p rogramming is d one as a single boa rd) Gener…

Zhejiang Neoden Technology Co., Ltd

center of this component, click save and back, it will return to the “PCB information” automatically.

 The data of “left top”on original board: on the alignment interface,find the left top panel,then find the component

same as the component that aligned on the “right top”,align the center of this component, click save and cancel, it will

return to the “PCB information” automatically.

 The data of “left bottom”on original board:on the alignment interface,find the left bottom panel,then find the

component same as the component that aligned on the “right top”, align the center of this component. After saving the

data, it will return to the “PCB information” automatically.

The data of “left bottom”on mirror board:on the alignment interface,find the left bottom panel,then find the component

same as the component that aligned on the “right top”, align the center of this component. After saving the data, it will

return to the “PCB information” automatically.

After setup, click “create panelized list”, the panelized list will be generated accordingly in the blank. You can also

double-confirm each position by clicking “Align”. Note: The angel difference between original and mirror board is 180

degree, original board is 0 degree, mirror is 180 degree.



Skip: For the block component corresponding to the number entered in the panel number (edit box), if no

placement operation will be performed, then select “Yes” in the drop-down list.



Placement: For the block component corresponding to the number entered in the panel number (edit box), if

perform placement operation, then select ‘No’ in the drop-down list.

 Recognition: Used for bad board detection. The current bad board detection function is still under development

and cannot be used yet.

4. Coordinate information

4.1 PCB Mark setting

PCB Mark setting interface see below fig.：

1.PCB Mark Point

（1）Panelized mark point

It is mainly used for multiple identical PCB boards consistent of the whole board, when place every panel board, the

machine will rescan small panel board’s mark point.

（2）Single mark point

Zhejiang Neoden Technology Co., Ltd

It is mainly used for a single PCB board and multiple identical PCB boards consistent of the whole board (Notice:

coordinate programming is done as a single board) Generally, need to select 2 or 3 mark points.

2. Mark point alignment

（1）Manual alignment:

If the fiducial point quality is poor and the recognition is not accurate, the reference position can be determined manually.

If there is no fiducial point on the PCB, which can through some location holes and set up some special reference point

manually to replace and confirm reference position. Note: Generally use SMD1 coordinate in chip list and the one that is

relatively easy to find far away from SMD1 as fiducial points .In this way, the relative placement effect will be better during

placement, the reference point is determined manually.

(2) Auto alignment

The machine will scan and align fiducial points automatically.

3.Mark Point information

（1）Mark point coordinate

Import the coordinate automatically status: the data collection of fiducial point, which through PCB circuit board to find

fiducial point coordinate information directly, and input directly.

Manual programming status: Select fiducial point on the list and click “align”, enter the image capture page, and then find

the center of the fiducial point via movement, select suitable light source and brightness, click "Mark align" see below

figure, and then click "Save and Back" to go back to main page.

（2）Min, max value

Zhejiang Neoden Technology Co., Ltd

It means the size of mark point, it has a floated value, which can prevent recognizing mark point wrongly.

（3）Light source

Light source divide into inner、middle、 outer、inner and middle、middle and outer, whole lights. The user can make

adjustments accordint to fiducial point recognition situation.

（4）Brightness

The user can adjust the brightness when align the fiducial point according to actual situation.

Selection of light source and brightness: The user can lock the location of the fiducial point through the XY position lock

interface, select the light source and brightness through the recognition of the Mark camera on the right, and fill the

corresponding parameters into the mark point information.

（5）Range

If there are interference points near the Mark point, you can input a certain value and ensure identify the Mark point more

accurately.

（6）Circle Degree

Input reasonable circle degree value,can avoid interference from other points effectively.

（7）Mode

Dividing into white point and black point, select black point mode if have hole and bright point,select white point mode if

have bright point.

（8）Camera

Support select left camera and right camera(user can select the camera for calibration according to the actual situation),also

can select default setting camera. If user select camera that can’t reach the position, the machine will use corresponding

camera during work.

（9）Mark point add and delete

Click “new” to add new fiducial point(base on mode of the latest fiducial point). Click ”delete” to remove the selected

fiducial point you want.

4.2 Component list setting

Function: display the information and mounting order of components. The components’ quantity and mounting information

can be added through manual programming or importing files , see below figure: