User-Manual-NeoDen9-PNP-machine.pdf - 第36页
36 Zhejiang Neoden T echnol ogy Co., Ltd of the chip, click " point 1", then select the pin center o f the u pper right foot op posite to left 1, click "po int 2", and the n clic k the middle poin t. …
35
Zhejiang Neoden Technology Co., Ltd
the adjustment is complete, just save it.
（10）Head Home back: click to move the head back to original left top position.
（11）Nozzle Replace: click to replace nozzles, the head will move to its position for easier replacement.
（12）Head Nozzle: click to test rotation, suction, blow and moving down functions of nozzle NO.1-NO.6.
（13）Width Initialize: initialize the width of rails back to zero.
（14）Width Set: after the initialization of rails width, enter the expected width, click Width Set, the rails be widened
accordingly.
（15）Introduction of Lock interface, as below fig.
Save and back：After align the center of components,click “save and back”to save the date.
Close and Back: Refer to exit the current interface.
Align method：Include left mark camera,nozzle 1-6,right mark camera,choose the alignment method according to the
actual situation,right side will show the real image by mark camera alignment.
Nozzle Down Test：
When mark cameras are selected as the alignment mode, this function is gray and inoperable.
When selecting nozzle 1-6, this interface turns black and can be operated. The user must first lock the position, enter a
reasonable height value, and then click the nozzle down test button to measure whether the reclaiming height is reasonable.
(Note: when locking the interface to test the reclaiming height of Feida, feeder will not open automatically. You can select
the material above the edge of thecomponent to measure.)
Point 1, Point 2, Mid-point：This operation is used to select the center position of some components.
For example, select " left mark camera" as alignment mode. First select the center of the first pin of the lower left foot
36
Zhejiang Neoden Technology Co., Ltd
of the chip, click "point 1", then select the pin center of the upper right foot opposite to left 1, click "point 2", and then click
the middle point. The machine will automatically calculate the center position of the chip.
Light source: outer ring,middle ring,Inner ring,Mark point generally select to use outer or inner ring,select
corresponding light source according to PCB kind.
Brightness: Image recognize brightness can be adjusted on the drop-down list.
9. System Setup
If any revision is required, we suggest you contact our engineer to get detailed instruction first. (P.S.
All parameters were set up before shipping, usually no adjustment is required.) This section will
provide a brief introduction for all parameters, to get detailed adjustment instruction, please contact
our technical engineer.
Right buttons functions:
Config save: to click Save after changing the parameter.
Administrator login: to prevent any misoperation, this interface will be inactive and greys out. To make it inactive,
Administrator needs to login.
Warning: this part aims at machine’s global parameter settings, any modified
parameter will influence all working files, when modify this part please consider
seriously.
37
Zhejiang Neoden Technology Co., Ltd
Change password: before Administration login in, this function is not visible.
If the password needs to be changed, please login and click Change password. A window will pop out, enter the original
password. Then follow steps to enter the new password. A successful window will pop out when it’s finished.
Version: the current software version will be displayed below.
When any software upgrade is required, please copy the upgrade file into the subdirectory of U disk, click “software
upgrade” to load it. Then follow instructions to upgrade it.
English: this machine supports Chinese and English. To convert it into English, a password is required.
9.1 Feeder Position Config
This interface is used to setup pick offset and test feeding for each feeder.
The left column refers to feeder No., Pick X and Pick Y refer to the coordinates of pick offset. After “click to align”, this
interface will be displayed. Align the center of component (edge of tablet), then save it.