X-Series-Maintenance-Manual(1).pdf - 第40页
Minor Maintenance Maintenance Tasks for the Conv eyor Consumables, Spare and Wear P arts, Tools 40 Maintenance Manual SIPLACE X Series Maintenance Tasks for the Conv eyor 4.4 Maintenance Tasks for the Conveyor Consumable…
Minor Maintenance
Performing Maintenance Tasks Maintenance Tasks for the Component Feed Device
Maintenance Manual SIPLACE X Series 39
Removing an d Preserving th e Magnetic Stri p on the Com ponent Troll ey for S Feeder Mo dules
4.3.3.4 Removing and Preserving the Magnetic Strip on the Component Trolley for S Feeder Modules
► Return the feeders to the feeder area.
► Clear the feeder area.
► Remove any loose components from the component
feeder table using the vacuum cleaner.
► (1) Use a whetstone to remove any bumps on the
magnetic rail.
► (2) Preserve the feeder area using a lint-free cloth
sprayed with WD40.
► Vacuum up any loose components from the tape
container and remove any unwanted stickers and
adhesive tape.
NOTICE
Pay attention to location and connection
► Make sure that each feeder is in the correct location and is connected properly.
Minor Maintenance
Maintenance Tasks for the Conveyor Consumables, Spare and Wear Parts, Tools
40 Maintenance Manual SIPLACE X Series
Maintenance Tasks for the Conveyor
4.4 Maintenance Tasks for the Conveyor
Consumables, Spare and Wear Parts, Tools
4.4.1 Consumables, Spare and Wear Parts, Tools
▪ Interflon Fin Super (Teflon oil) [03017760-xx]
▪ Lint-free cloths [03082092-xx]
▪ Ethanol
▪ SIPLACE cleansing tissue [00315253-xx]
▪ Protective latex gloves [00372972-xx]
▪ Set of Phillips screwdrivers
▪ ESD wristband [00320279-xx]
▪ Vacuum cleaner
Preparatory Steps
4.4.2 Preparatory Steps
► There must be no PCBs in the machine during the following maintenance steps.
► Make a note of the current conveyor width.
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 11].
Performing Maintenance Tasks
4.4.3 Performing Maintenance Tasks
Vacuuming the Conveyors, Conveyor Belts, Sensors and Lifting Table
4.4.3.1 Vacuuming the Conveyors, Conveyor Belts, Sensors and Lifting Table
CAUTION
Loose components
Loose components on the PCB conveyor could cause faults.
► Use the vacuum cleaner to remove all loose
components on and around the PCB conveyor. Pay
particular attention to the areas near the lifting table,
the width adjustment, the trailing cables and the
conveyor belts.
Minor Maintenance
Performing Maintenance Tasks Maintenance Tasks for the Conveyor
Maintenance Manual SIPLACE X Series 41
Cleaning and Preserving t he Hexagonal Sha fts
4.4.3.2 Cleaning and Preserving the Hexagonal Shafts
Cleaning the Fixtu re Tape
4.4.3.3 Cleaning the Fixture Tape
Cleaning and Preserving t he Recirculatin g Ball Screws of the Width Adjustment
4.4.3.4 Cleaning and Preserving the Recirculating Ball Screws of the Width Adjustment
► Apply Teflon oil to a lint-free cloth and clean the
hexagonal shafts (1) in the conveyor.
Alternatively you can also use a SIPLACE cleansing
tissue.
► Repeat the procedure for all hexagonal shafts in the
conveyor.
CAUTION! Risk of cutting!
The fixing strip has a sharp edge.
► Clean the fixing strip of the width adjustment
clamping unit using a lint-free cloth moistened with
ethanol.
► Clean and preserve the recirculating ball screw (1) by
running a SIPLACE cleansing tissue along the thread
of the screw.
► Repeat this procedure for all recirculating ball
spindles on the conveyor.