X-Series-Maintenance-Manual(1).pdf - 第41页
Minor Maintenance Performing Maintenance Tasks Maintenance Tasks for th e Conveyor Maintenance Manual SIPLACE X Series 41 Cleaning and Preserving t he Hexagonal Sha fts 4.4.3.2 Cleaning and Preserving the Hexagonal Shaft…
Minor Maintenance
Maintenance Tasks for the Conveyor Consumables, Spare and Wear Parts, Tools
40 Maintenance Manual SIPLACE X Series
Maintenance Tasks for the Conveyor
4.4 Maintenance Tasks for the Conveyor
Consumables, Spare and Wear Parts, Tools
4.4.1 Consumables, Spare and Wear Parts, Tools
▪ Interflon Fin Super (Teflon oil) [03017760-xx]
▪ Lint-free cloths [03082092-xx]
▪ Ethanol
▪ SIPLACE cleansing tissue [00315253-xx]
▪ Protective latex gloves [00372972-xx]
▪ Set of Phillips screwdrivers
▪ ESD wristband [00320279-xx]
▪ Vacuum cleaner
Preparatory Steps
4.4.2 Preparatory Steps
► There must be no PCBs in the machine during the following maintenance steps.
► Make a note of the current conveyor width.
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 11].
Performing Maintenance Tasks
4.4.3 Performing Maintenance Tasks
Vacuuming the Conveyors, Conveyor Belts, Sensors and Lifting Table
4.4.3.1 Vacuuming the Conveyors, Conveyor Belts, Sensors and Lifting Table
CAUTION
Loose components
Loose components on the PCB conveyor could cause faults.
► Use the vacuum cleaner to remove all loose
components on and around the PCB conveyor. Pay
particular attention to the areas near the lifting table,
the width adjustment, the trailing cables and the
conveyor belts.
Minor Maintenance
Performing Maintenance Tasks Maintenance Tasks for the Conveyor
Maintenance Manual SIPLACE X Series 41
Cleaning and Preserving t he Hexagonal Sha fts
4.4.3.2 Cleaning and Preserving the Hexagonal Shafts
Cleaning the Fixtu re Tape
4.4.3.3 Cleaning the Fixture Tape
Cleaning and Preserving t he Recirculatin g Ball Screws of the Width Adjustment
4.4.3.4 Cleaning and Preserving the Recirculating Ball Screws of the Width Adjustment
► Apply Teflon oil to a lint-free cloth and clean the
hexagonal shafts (1) in the conveyor.
Alternatively you can also use a SIPLACE cleansing
tissue.
► Repeat the procedure for all hexagonal shafts in the
conveyor.
CAUTION! Risk of cutting!
The fixing strip has a sharp edge.
► Clean the fixing strip of the width adjustment
clamping unit using a lint-free cloth moistened with
ethanol.
► Clean and preserve the recirculating ball screw (1) by
running a SIPLACE cleansing tissue along the thread
of the screw.
► Repeat this procedure for all recirculating ball
spindles on the conveyor.
Minor Maintenance
Maintenance Tasks for the Conveyor Final Work
42 Maintenance Manual SIPLACE X Series
Cleaning and Preserving t he Guide Shafts of the Wid th Adjustment
4.4.3.5 Cleaning and Preserving the Guide Shafts of the Width Adjustment
Cleaning and Pre serving t he Guide Shaft of the Conv eyor Sides
4.4.3.6 Cleaning and Preserving the Guide Shaft of the Conveyor Sides
Final Work
4.4.4 Final Work
► Reconnect all clamps, where applicable.
► Set back to the original conveyor width.
► Apply Teflon oil to a lint-free cloth and clean the
bottom (1) and top (2) guide shaft of the width
adjustment.
Alternatively you can also use a SIPLACE cleansing
tissue.
► Repeat the procedure for all width adjustment guide
shafts on the conveyor.
► Clean and preserve the guide shaft (1) for the
conveyor sides with a SIPLACE cleansing tissue.
► Repeat the procedure for all guide shafts on the
conveyor sides.