X-Series-Maintenance-Manual(1).pdf - 第71页
Major Maintenance Consumables, Spare and Wear Parts , Tools Maintenance Work on the Gantry Maintenance Manual SIPLACE X Series 71 Maintenanc e Work on the Gantry 5.4 Maintenance Work on the Gantry Consumable s, Spare and…
Major Maintenance
Maintenance Tasks for the Component Docking Unit Consumables, Spare and Wear Parts, Tools
70 Maintenance Manual SIPLACE X Series
Maintenance Tasks for the Component Docking Unit
5.3 Maintenance Tasks for the Component Docking Unit
Consumables, Spare and Wear Parts, Tools
5.3.1 Consumables, Spare and Wear Parts, Tools
▪ Sheet of DIN A3 paper (or 2x A4)
▪ Adhesive tape
▪ Scissors
▪ ESD wristband [00320279-xx]
Preparatory Steps
5.3.2 Preparatory Steps
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 11].
Performing Maintenance Tasks
5.3.3 Performing Maintenance Tasks
Functio n Test of Used Tape Cutter
5.3.3.1 Function Test of Used Tape Cutter
CAUTION
Risk of cutting
Observe the safety instructions for the cutter!
► "1.1.5 Safety Instructions for Work on the Cutting Device" [ ➙ 9]
► Insert a sheet of DIN A3 paper or two DIN A4 sheets
attached to one another into the empty tape duct.
NOTICE! A DIN A4 sheet on its own is too short
to reach the tape cutter.
► Attach the sheet of paper with adhesive tape to the
empty tape duct.
Make sure that there is no paper protruding upwards
in the placement head travel range.
► Start the cutting process in the software
► Take the sheet of paper out of the empty tape duct
again.
If it has not been cut through accurately, replace the
cutting blades. Please contact your SIEMENS
Service team for this work.
Major Maintenance
Consumables, Spare and Wear Parts, Tools Maintenance Work on the Gantry
Maintenance Manual SIPLACE X Series 71
Maintenanc e Work on the Gantry
5.4 Maintenance Work on the Gantry
Consumables, Spare and Wear Parts, Tools
5.4.1 Consumables, Spare and Wear Parts, Tools
▪ Lint-free cloths [03082092-xx]
▪ SIPLACE cleansing tissue [00315253-xx]
▪ Klüberplex BEM 34-132 lubricant, 1 kg tin [00374565-xx]
▪ Protective latex gloves [00372972-xx]
▪ Cotton gloves [00359087-xx]
▪ ESD wristband [00320279-xx]
▪ Grease gun with hose for Y axis (volume applied: approx. 0.4 g) [00374563-xx]
▪ Grease gun with nozzle for X axis (volume applied: approx. 0.13 g) [00374564
-
xx]
▪ DIN71412 - A M6 lubrication nipple [03036936-xx], if required
▪ Cooling air set (black) [03003704-xx] or cooling air set (white) [03030955-xx], if required
▪ Set of Allen wrenches
▪ A high-precision set of scales (recommended minimum measuring accuracy: 1 g)
Preparatory Steps
5.4.2 Preparatory Steps
► There must be no PCBs on the PCB conveyor for the following jobs.
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 11].
► Prepare the grease gun.
Major Maintenance
Maintenance Work on the Gantry Preparatory Steps
72 Maintenance Manual SIPLACE X Series
Filling the Grease Gun
5.4.2.1 Filling the Grease Gun
► Pull back the grease gun plunger. It must lock into
place.
► Open the grease gun by unscrewing the top section.
► Fill the grease gun with suitable grease. Use a clean
spatula.
Try to fill the gun with grease without trapping in any
air pockets.
► Close the grease gun by screwing the top section
back on.
► Loosen the lock on the back of the grease gun. The
spring force moves the plunger forward.
► Push back the ball on the vent screw to vent the
grease gun. Use a screwdriver or similar tool to help
you.
CAUTION! Always vent the grease gun once
you have finished greasing the machine!
► Press the trigger until the grease emerges from the
front of the gun.
► Remove excess grease with a lint-free cloth.
The grease gun is now ready for use.