00198628-01_Option_Stationäre-Kamera_TX12_V2_de_en.pdf - 第70页

1 Introduction 1.3 Other instructions 70 Assembly Instructions / Montageanleitung SIPLACE TX-Series V2 Stationary Camera Type 25/33 Stationäre Kamera Typ 25/33 10/2018 Do not allow modules with chargeable and highly insu…

1 Introduction

1.3 Other instructions

Assembly Instructions / Montageanleitung SIPLACE TX-Series V2 Stationary Camera Type 25/33 Stationäre Kamera

Typ 25/33 10/2018

1.3 Other instructions

1.3.1 Environmentally-friendly disposal of materials and components

Our products are manufactured using only materials and parts that can be easily separated and

disposed of in an environmentally-friendly way.

NOTICE

Observe the applicable regulations

The company operating the system has sole responsibility for the proper, environmentally-

friendly disposal of machines, working materials, consumable materials and wear parts.

► Please observe your national statutory provisions for waste disposal and environ-

mental protection.

1.3.2 Use of original accessories and spare parts

Only use original spare parts and authorized accessories. The use of other parts will affect safety

and will invalidate the liability for any consequential damage.

1.3.3 ESD guidelines

1.3.3.1 What does ESD mean?

Fig.7: ESD label

Almost all of the modules in use today are equipped with highly integ-

rated Metal-Oxide-Semiconductor (MOS) blocks and components.

The manufacturing techniques used mean that these electronic com-

ponents are extremely sensitive to overvoltage and thus to electro-

static discharge.

The abbreviation for such modules is "ESD" (Electrostatic Sensitive

Device). "ESD" is used internationally. The following symbol on cab-

inet rating plates, racks or packaging indicates that components

which are sensitive to electrostatic discharge have been used and

thus that the modules concerned are also touch-sensitive.

ESDs can be destroyed by voltages and power levels that are far below the level that can be per-

ceived by humans. Such voltages occur if a person touches a component or module without

earthing themselves. Components that are exposed to such overvoltages do not generally appear

to be defective immediately - incorrect behavior starts after the component or module has been in

operation for some time.

1.3.3.2 Important measures to protect against static charging

► Most plastics can easily become charged and must therefore be kept away from at-risk com-

ponents.

► Always ensure that people, the workplace and packaging are safely earthed when handling

electrostatic sensitive components.

1.3.3.3 Handling ESD modules

Do not touch electronic modules unless it is absolutely essential to do so in order to carry out other

work. If it is necessary, make sure that you do not touch the pins or printed conductors when you

pick up flat modules.

Do not touch components unless:

●

you are constantly earthed by an ESD wrist strap or

●

You are wearing ESD shoes or ESD shoe earthing strips on an ESD floor.

Always discharge yourself before you touch an electronic module. To do this, simply touch a con-

ductive and earthed object immediately before you touch the module (such as unpainted parts of a

switch cabinet, a water pipe, etc.).

1 Introduction

1.3 Other instructions

70 Assembly Instructions / Montageanleitung SIPLACE TX-Series V2 Stationary Camera Type 25/33 Stationäre Kamera

Typ 25/33 10/2018

Do not allow modules with chargeable and highly insulating materials to touch one another,

e.g. plastic films, insulating table surfaces or items of clothing made from synthetic fibers.

Always place the modules on a conductive surface (table with an ESD coating, conductive

ESD foam, ESD bag or container).

Do not move the assemblies near to data view devices, monitors or television units. Keep a

minimum distance of 10 cm to monitors.

1.3.3.4 Measurements and modifications to ESD modules

Do not take measurements on the modules unless the following conditions are fulfilled:

●

The measuring device is earthed (e.g. via PE conductors) or

●

You discharge the measuring head just before taking measurements with a potential-free

measuring device (e.g. by touching an unpainted metal part of the controller casing).

► Always use an earthed soldering iron if you carry out any soldering work.

1.3.3.5 Dispatching ESD modules

► Always store modules and components in conductive packaging (e.g. metallized plastic bags

or metal sleeves) and dispatch them in conductive packaging.

► If the packaging is not conductive, place the modules in a conductive envelope before

packaging. Use conductive expanded rubber, ESD bags, domestic aluminum foil or paper,

for example. NEVER use plastic bags or film.

► If the module has integral batteries, ensure that the conductive packaging does not touch or

short circuit the battery terminals and, if necessary, first cover the terminals with insulating

tape or material.

1.3.4 Validity of document

This document is valid for the following machine types:

●

SIPLACE TX V2-Series

The work described in this manual is divided into modules and is largely identical for all machine

types:

●

If the work required for specific machines differs from the standard procedure, this will be

indicated with reference to the machine number, series and delivery state.

●

Illustrations are only shown as examples. For example, the illustration of a specific machine

type or a machine with different paint finish does not imply that the information following the

illustration only applies to the shown machine type.

Please read the circuit diagram folder for any electrical checks.

●

Detailed circuit diagrams folder for SIPLACE TX-Series (up to no. 499)

[DE+EN: 00197933-xx]

●

Detailed circuit diagrams folder for SIPLACE TX-Series (from no. 500) [DE+EN: 00198274-xx]

●

Detailed circuit diagrams SIPLACE TX V2-Series [DE+EN: 00198460-xx]

●

Detailed circuit diagrams folder for SIPLACE X-Series S (up to Gxxxx) [DE+EN:00197021‑xx]

●

Detailed circuit diagrams folder for SIPLACE X-Series S (from Hxxxx) [DE+EN:00197920‑xx]

●

Detailed circuit diagrams folder for SIPLACE SX1/SX2/DX1/DX2 (up to Kxxxx)

[DE+EN:00196475-xx]

●

Detailed circuit diagrams folder for SIPLACE SX1/SX2 V2 (from Lxxxx)

[DE+EN:00196979-xx]

●

Detailed circuit diagrams folder for SIPLACE SX1/SX2 V2 (from Nxxxx)

[DE+EN:00197899-xx]

1 Introduction

1.4 Staff qualifications and training

Assembly Instructions / Montageanleitung SIPLACE TX-Series V2 Stationary Camera Type 25/33 Stationäre Kamera

Typ 25/33 10/2018

1.3.5 Release History

Document

SIPLACE TX-Series V2

Stationary camera type 25/33

Assembly Instructions

Edition Amendments

10/2018 First edition

1.4 Staff qualifications and training

Qualified or adequately trained personnel means that these people are familiar with the setting up,

operation and maintenance of the machine and the add-on devices and are suitably qualified, e.g.:

●

Have been trained, instructed or authorized to switch on and off, isolate, earth and identify

electrical circuits and system components in accordance with normal safety standards.

●

Have been trained or instructed in the upkeep and use of appropriate safety equipment in

accordance with normal safety standards.

●

Have received first aid training.