CP7 training(6.0) (1).pdf - 第6页
FK-9F98-27 CP-7 Series T raini ng T ext for Service Engineers Edition 6.0 Chapter 1. Initial Set-up [2/4] 1.3 Recovery and Applicat ion Soft ware Installation It will take a tot al of approximately 30 minutes to inst all…
FK-9F98-27 CP-7 Series Training Text for Service Engineers
Edition 6.0 Contents-
List of Current Pages
Chapter 8 Placing Accuracy Measurement…………….……….(Edition 6.0)
(section No.) (Page No.)
8.1 PAM Calibration 8-1
Chapter 9 Miscellaneous Adjustments………………...…………(Edition 6.0)
(section No.) (Page No.)
9.1 Backup pin Adjustment 9-1
9.2 Air / Vacuum Pressure Sensor Calibration 9-2
9.3 D-axis Cover Installation 9-3
9.4 PCB Set Check Sensor Adjustment 9-5
9.5 Oil Pressure Sensor Amp Adjustment 9-5
Chapter 10 Options………………………………..…………..…...(Edition 6.0)
(section No.) (Page No.)
10.1 Parts Thickness Confirmation Sensor Adjustment 10-1
10.1.1 Machine Setting 10-2
10.1.2 Sensor Head Alignment 10-2
10.1.3 Sensor Amplifier Output Voltage Adjustment 10-3
10.1.4 How to avoid problems while adjusting the voltage 10-5
10.1.5 Amplifier SW and LED functions 10-5
10.2 Vacuum Backup Pin Adjustment 10-6
Chapter 11 Recovery of Absolute Encoder Errors…….…..……(Edition 6.0)
(section No.) (Page No.)
11.1 Recovery of Absolute Encoder Errors 11-1
Chapter 12 Electrical System…….…..…………………………..(Edition 6.0)
(section No.) (Page No.)
12.1 Monitoring the I/O signals on CP-7 Series Machines 12-1
12.2 Servo System Interface 12-3
12.3 Servo Command PCB (LED) Function 12-4
12.4 Fuses and Batteries 12-5
12.5 The Absolute Encoder System 12-6
12.6 CP7 Series Electrical Block Diagrams 12-8
Block 1 12-8
Block 2 12-9
Supplemental Information
1. PAM Operation Manual
2. BIOS Setting Manual
A: BIOS version 1.00.04 (V1.20 and later)
3. Servo Pack Error Code Listing
Fuji Machine Mfg. Co., Ltd. (Okazaki)
SMT Equipment Quality Assurance Dept.
CS Section
VIII
FK-9F98-27 CP-7 Series Training Text for Service Engineers
Edition 6.0 Chapter 1. Initial Set-up [2/4]
1.3 Recovery and Application Software Installation
It will take a total of approximately 30 minutes to install the recovery and system software and
re-establish communications with the host computer.
1. Put the “Recovery CD” into the CD-ROM drive, which is at the front of the M/C (center
box). When installing the CD, the m/c power must be ON.
The recovery disk contains the Windows NT Operating System.
2. Press the E-stop and Power OFF to shut the machine down.
Note: If the machine display is locked up, Press the “Windows” key on the keyboard
(connected to the machine) and select [Shut down] from the lower left menu.
3. Turn OFF the UPS when the following message appears:
“It is now safe to turn off your computer.”
4. Wait five seconds or so and then turn the UPS ON again.
5. Press [SYSTEM ON] from the machine operation panel.
6. When the machine begins to boot, the display will pause after the following message:
“strike a key when ready”. Press the space key on the keyboard three times and
installation will begin. (It will take 3 to 5 minutes for registration)
7. Once registration is finished, the following message will appear on the screen:
“strike a key when ready”.
8. Press the space key once and quickly swap the recovery CD with the Fuji application CD.
9. The FUJI Installation software will start and the following message will show:
“Does it install it?” Press the [Enter] key to enter “YES”.
10. There will be a display to enter the Product ID. Copy the Product ID from the license
“Certificate of Authenticity” and press [Enter]. (The “Certificate of Authenticity” can be found
in a pocket located in one of the rear enclosures) A message will show to confirm the
Product ID. Confirm that the correct ID was entered and then press [Enter].
11. Installation of the “Application CD” will start. (It will take about approx. 20 minutes for
registration.)
12. When registration is completed, the following message will show:
“Please remove the CD-ROM”. Remove the CD from the CD-ROM drive and press
[Enter]. The machine will automatically reboot. The procedure is completed if an error does not
occur.
Note:
If the following message “strike a key when ready” does not appear and Windows NT
starts, (even if the machine is rebooted after the “recovery CD” is put into the CD-ROM) the
BIOS settings may be wrong. In this case, check all BIOS settings. (refer to the BIOS set-
up manual located in the supplement section of this manual, or refer to the Fuji web-site to
download the BIOS setting manual.)
Fuji Machine Mfg. Co., Ltd. (Okazaki)
SMT Equipment Quality Assurance Dept.
CS Section
1-2
FK-9F98-27 CP-7 Series Training Text for Service Engineers
Edition 6.0 Chapter 1. Initial Set-up [3/4]
1.4 Configuring the Machine Network Settings
After installation of the recovery and application software, it is necessary to set up the network
settings at the machine. All setting data is cleared from the machine once the recovery disk has
been used. Carry out the procedure below in order to establish communications with the host
PC.
1. After the machine boots from recovery and application software installation, press the
following commands to enter the network settings.
[Maintenance] → [System] → [Network]
2. Enter the machine Nickname (Host), IP address and Subnet Mask.
(This information should be provided by the network administrator at the user site.)
Figure 2
3. After setting the above, close the window and save the changes. It is now necessary to re-
boot the machine in order for the data to be registered.
4. After the machine has been re-booted, transmit the appropriate calibration data and
programs to the machine. After doing so, it will be necessary once again to re-boot the
machine.
Fuji Machine Mfg. Co., Ltd. (Okazaki)
SMT Equipment Quality Assurance Dept.
CS Section
1-3