3OM-1343-008_w.pdf - 第334页
7-3 AKFEDT -ID Input Conveyor Y Position arrange speed setup (% deceleration) [%] Output Conveyor Y Position arrange speed setup (% deceleration) [%] PCB Locate mode Stage 1 Operation Std / Speci fi cation value The 1st s…
7-2
AKFEDT-ID
PCB transfer
speed des
Avoid
comp
deviations
Input Speed 1
[mm/sec]
Speed 2
[mm/sec]
Acceleration
[G]
Between
Stages
Speed 1
[mm/sec]
Speed 2
[mm/sec]
Acceleration
[G]
Output Speed 1
[mm/sec]
Speed 2
[mm/sec]
Acceleration
[G]
Stop
position
control
Input Timer
[msec]
Position [mm]
Position-
ing 1
Timer
[msec]
Position [mm] + / -
Center Timer
[msec]
Position [mm] + / -
Position-
ing 2
Timer
[msec]
Position [mm] + / -
Output Timer
[msec]
Position [mm] + / -
0601-002
Pattern Program Data Sheets
7-3
AKFEDT-ID
Input Conveyor
Y Position arrange speed setup (% deceleration) [%]
Output Conveyor
Y Position arrange speed setup (% deceleration) [%]
PCB Locate
mode
Stage 1 Operation Std / Specifi cation value
The 1st sp dclr setting
([%] deceleration) [%]
The 2nd sp dclr setting
([%] deceleration) [%]
Z clamp Delay Timer 1
[msec]
Delay Timer 2
[msec]
Operation
waiting time
[msec]
Stage 2 Operation Std / Specifi cation value
The 1st sp dclr setting
([%] deceleration) [%]
The 2nd sp dclr setting
([%] deceleration) [%]
Z clamp Delay Timer 1
[msec]
Delay Timer 2
[msec]
Operation
waiting time
[msec]
Placement mode Stage 1 Placement / Pass
Stage 2 Placement / Pass
Recovery
regulation
U-N Stage 1 Disable / Enable
Stage 2 Disable / Enable
Block Stage 1 Disable / Enable
Stage 2 Disable / Enable
0601-002
Pattern Program Data Sheets
7-4
AKFEDT-ID
Pattern Program Name
Comment 1
Comment 2
Date of Preparation
Prepared by
Operation Data
PEC Recognition Data
PEC recognition function Disable / Enable
Correction algorithm Standard/Mode #1
PEC recognition Mode Global Zone 1 Disable/1 Point/2 Point/3 Point
Zone 2 Disable/1 Point/2 Point/3 Point
Zone 3 Disable/1 Point/2 Point/3 Point
Zone 4 Disable/1 Point/2 Point/3 Point
Zone 5 Disable/1 Point/2 Point/3 Point
Image Disable / Enable
Local Disable / Enable
Fiducial mark Zone 1
#1 X (Horizontal) [mm] + / -
Y (Vertical) [mm] + / -
Mark Code
#2 X (Horizontal) [mm] + / -
Y (Vertical) [mm] + / -
Mark Code
#3 X (Horizontal) [mm] + / -
Y (Vertical) [mm] + / -
Mark Code
Zone 2 #1 X (Horizontal) [mm] + / -
Y (Vertical) [mm] + / -
Mark Code
#2 X (Horizontal) [mm] + / -
Y (Vertical) [mm] + / -
Mark Code
#3 X (Horizontal) [mm] + / -
Y (Vertical) [mm] + / -
Mark Code
Zone 3 #1 X (Horizontal) [mm] + / -
Y (Vertical) [mm] + / -
Mark Code
#2 X (Horizontal) [mm] + / -
Y (Vertical) [mm] + / -
Mark Code
#3 X (Horizontal) [mm] + / -
Y (Vertical) [mm] + / -
Mark Code
0601-002
Pattern Program Data Sheets