SMW200A_specs_en_3606-8037-22_v2700.pdf - 第60页

Version 27.00, October 2024 60 Rohde & Schwar z R&S ® SMW200A Vec tor Signal Generator Clock see section Wideban d baseband generator (R &S ® SMW-B9 option ) – arbitrary wave form mode Triggering see section …

Version 27.00, October 2024

Rohde & Schwarz R&S

SMW200A Vector Signal Generator 59

Single carrier delay

Setting range

0 s to 1 s

Setting resolution

1 ns

ARB Ethernet upload (R&S

SMW-K507 option)

ARB Ethernet upload is a sub mode of arbitrary waveform mode, see section Wideband baseband generator (R&S

SMW-B9 option) –

arbitrary waveform mode. This feature allows a fast upload und playback of waveform I/Q samples from an external source via UDP

over a QSFP+ LAN interface into a Rohde & Schwarz signal generator (R&S

SMW200A).

The waveform parameter and I/Q samples are transferred using special transmission commands (Rohde & Schwarz upload protocol,

see K507 user manual).

At least one R&S

SMW-B9 wideband baseband generator option must be installed. If two R&S

SMW-B9 options are installed (signal

paths A and B), the ARB Ethernet upload can be used either on signal path A or B with one R&S

SMW-K507 option. For simultaneous

usage on signal paths A and B, two R&S

SMW-K507 options must be installed.

ARB Waveform

File size, technical specification

see section Wideband baseband

generator (R&S

SMW-B9 option) –

arbitrary waveform mode

File generation

see R&S

SMW200A user manual, section

Using the Arbitrary Waveform Generator

(ARB)

Upload transmission protocol

R&S

ARB upload protocol

see K507 user manual

Marker signals

Number of marker signals

Operating modes

waveform (unchanged), restart

Marker outputs

see section Wideband baseband

generator (R&S

SMW-B9 option) –

arbitrary waveform mode

Interface parameters

LAN interface

Connector

HS/DIGIQ 1, 2 on rear panel

QSFP+ (note the recommended extras

below)

Protocol

UDP over Ethernet

Data rate

10 Gigabit Ethernet or 40 Gigabit Ethernet

can be configured in user interface

10 Gbit/s, 40 Gbit/s

Extended sequencing (R&S

SMW-K502 option)

The R&S

SMW-K502 option enables waveform sequencing and real-time signal generation for ultra long playtime. Waveform

variations such as offset frequency, amplitude and phase are calculated in real-time and do not require precalculated waveforms.

The extended sequencing is controlled by the external R&S

Pulse Sequencer Software, a powerful software tool for simulating

complex sequencing scenarios.

At least one R&S

SMW-B9 option (wideband baseband generator) must be installed. If two R&S

SMW-B9 options are installed (signal

paths A and B), extended sequencing can be used either on signal path A or B with one R&S

SMW-K502 option. For extended

sequencing to be used simultaneously on signal paths A and B, two R&S

SMW-K502 options must be installed.

General settings

Modes

controlled by external

R&S

Pulse Sequencer Software

(R&S

SMW-K300 required)

pulse sequencer

Pulse sequencer mode

see R&S

Pulse Sequencer Software

specifications (PD 3607.1388.22)

Waveform segments

Segment length

1 sample to 64 Msample

Minimum memory allocation

64 sample

Maximum number of segments

depends on segment lengths and

baseband generator ARB memory size

Waveform sequences

Sequencing

continuously repeating

Maximum number of segments per

sequence

depends on segment lengths and

baseband generator ARB memory size

Maximum number of segment repetitions

Version 27.00, October 2024

60 Rohde & Schwarz R&S

SMW200A Vector Signal Generator

Clock

see section Wideband baseband

generator (R&S

SMW-B9 option) –

arbitrary waveform mode

Triggering

see section Wideband baseband

generator (R&S

SMW-B9 option) –

arbitrary waveform mode

Marker signals

Number of marker signals

Operating modes

marker at every start of sequence

restart

marker 1 embedded in waveform

unchanged

marker at every pulse

pulse

Marker outputs

see section Wideband baseband

generator (R&S

SMW-B9 option) –

arbitrary waveform mode

Marker delay

see section Wideband baseband

generator (R&S

SMW-B9 option) –

arbitrary waveform mode

Marker duration

see section Wideband baseband

generator (R&S

SMW-B9 option) –

arbitrary waveform mode

Real-time control interface (R&S

SMW-K503/-K504 options)

The R&S

SMW-K503/-K504 option enhances the R&S

SMW-B9 wideband baseband generator option by adding a dedicated 1 Gbit/s

LAN interface for pulse descriptor word (PDW) streaming. PDWs are streamed via the external LAN interface to control a real-time

sequencer on the R&S

SMW-B9. Either a precalculated waveform can be played back or certain signals such as rectangular pulses,

Barker codes and chirps can be generated in real time.

In addition to these different signal types, the interface provides agile switching of frequency, phase and amplitude. These variations

are calculated in real time.

The real-time control interface is controlled by an external simulator that streams the PDWs in a proprietary Rohde & Schwarz format.

At least one R&S

SMW-B9 wideband baseband generator option and one R&S

SMW-K502 option must be installed. If two

R&S

SMW-B9 options and two R&S

SMW-K502 options are installed (signal paths A and B), the real-time control interface can be

used either on signal path A or B with R&S

SMW-K503 or -K504 option. For simultaneous usage on signal paths A and B, two

R&S

SMW-K503/-K504 options must be installed. The R&S

SMW-K504 option increases the maximum PDW rate from 1 MPDW to

2 MPDW. Each R&S

SMW-K504 option requires an R&S

SMW-K503 option to be installed.

PDW parameters

PDW format

PDW

variant no. 1

32 byte fixed length

variant no. 2

32/48 byte fixed length

CNTRL PDW

16 byte fixed length

Controllable parameters

PDW

variant no. 1

time of arrival, frequency offset, amplitude

offset, phase offset, real-time modulation

on pulse (MOP, see real-time MOP types

below), I/Q waveform index

variant no. 2

time of arrival, rise time, fall time, edge

type (linear, cosine), repetitions (in burst

mode), frequency offset, amplitude offset,

phase offset, real-time modulation on

pulse (MOP, see real-time MOP types

below), I/Q waveform index

CNTRL PDW

absolute amplitude, absolute frequency

Setting granularity

Time

417 ps

Amplitude

16 bit (voltage based)

Phase

< 0.01°

Frequency

0.58 Hz

I/Q segments

Maximum individual segments

16 777 216

Length granularity

32 sample

Version 27.00, October 2024

Rohde & Schwarz R&S

SMW200A Vector Signal Generator 61

Time parameters

Maximum play time

variant no. 1

2 h

variant no. 2

521 h

Minimum pulse width

real-time

3.3 ns

I/Q segment

417 ps

Minimum PRI real-time signals

variant no. 1

with R&S

SMW-K503 option

1 µs

with R&S

SMW-K504 option

0.5 µs

variant no. 2

with R&S

SMW-K503 option

1 µs

with R&S

SMW-K504 option

0.5 µs without extension fields,

1 µs with extension fields

Minimum I/Q segment playback

repetition interval

1.0 µs

Real-time MOP types

Unmod

rectangular pulse

Linear FM

up, down, triangular

Maximum hirp deviation

±1 GHz

Phase

Barker

Barker codes

R3, R4a, R4b, R5, R7, R11, R13

Marker signals

Number of marker signals

Operating modes

pulse, restart, PDW

Marker outputs

see section Wideband baseband

generator (R&S

SMW-B9 option) –

arbitrary waveform mode

Marker delay

see section Wideband baseband

generator (R&S

SMW-B9 option) –

arbitrary waveform mode

Interface parameters

LAN interface

Connector

ADV DATA/CTRL 1, 2 on rear panel

RJ-45

PDW buffer

Size

536 870 656 byte

Pulse-on-pulse simulation (R&S

SMW-K315 option)

This option enhances the R&S

SMW-K502 option to simulate up to 6 true parallel instances of the extended sequencer in a single

instrument. It allows the generation of time overlapping pulse-on-pulse signals. As a result, up to 6 emitters can be generated

simultaneously in one R&S

SMW200A. If the R&S

SMW-K306 option is installed, each extended sequencer can also be used to

generate a group of interleaved emitters. In case of interleaving emitters, drop-out rates can be reduced by distributing emitters onto

more hardware resources.

Two R&S

SMW-B9 options (wideband baseband generator), two R&S

SMW-K502 options and at least two R&S

SMW-B15 options

(fading simulator and signal processor) must be installed. Depending on the operating mode, additional options are required:

Operating modes

radar signal generation with

R&S

Pulse Sequencer Software

pulse sequencer

radar signal generation using PDW

streaming with R&S

SMW-K503/-K504

options

real-time control interface

Minimum required options

operating mode: pulse sequencer

two R&S

SMW-B9, two R&S

SMW-K502,

two R&S

SMW-K300,

two R&S

SMW-K301,

two or four R&S

SMW-B15

operating mode: real-time control

interface

two R&S

SMW-B9, two R&S

SMW-K502,

two R&S

SMW-K503,

two or four R&S

SMW-B15

Number of extended sequencers

two R&S

SMW-B15 installed

four R&S

SMW-B15 installed