00193794-11_VD_SSW 505.05_de en.pdf - 第20页
Software Version Description, Station Software 505.05 07/2008 Edition 20 of 150 4 New features of st ation sof tware 505.05 4.1 Revision of the Forced Setup V e rification The forced setup verification at the SIPLACE pla…
Software Version Description, Station Software 505.05 07/2008 Edition
19 of 150
3.2.4 Machine controller
3.2.4.1 Machine controller HF, HF/3
Name Simicro CPU076
CPU / clock frequency PIII / 566 MHz
RAM memory 64 MB
Hard disk 6 GB
CD-ROM drive Yes
Floppy drive 3.5", 1.44 MB
Network 1 x 10/100Base-T
Table 3-5: Machine controller hardware
3.2.4.2 Machine controller S-25 HM, S-27 HM, HS-50, HS-50+, HS-60
Name Sicomp AMS – M54
CPU / clock frequency PI / 233 MHz
RAM memory 32 MB
Hard disk 504MB
CD-ROM drive No
Floppy drive 3.5", 1.44 MB
Network 1 x 10/100Base-T
Table 3-6: Machine controller hardware
Software Version Description, Station Software 505.05 07/2008 Edition
20 of 150
4 New features of station software 505.05
4.1 Revision of the Forced Setup Verification
The forced setup verification at the SIPLACE placement machine can be activated via SIPLACE Setup
Center. The forced setup verification monitors the verification status of individual tracks. Non-verified
tracks are disabled to force setup verification.
Forced setup verification is carried out with a connection to the station and requires successful setup
verification before production. This is implemented as follows: once an order or a packaging unit
changeover has been downloaded, the machine deactivates all divisions in which there are packaging
units for which no setup verification data has been received.
This means the line operator needs to successfully verify all the necessary components/packaging
units for the product before production can begin.
A detailed description can be found in the "Installation Manual SIPLACE Setup Center 3.0", item no.
00195642-xx.
4.1.1 Requirements
The forced setup verification requires SIPLACE Pro as of Version 5.0 and SIPLACE Setup Center as of
Version 3.0.
4.2 Shutterless feeder – Teaching pickup position
In some cases the PCB camera cannot reach the component pickup position in a shutterless feeder in
the middle. This can happen with shutterless feeder at the following machines and setup locations:
- S27
- HF/3, setup location 4
If the component pickup position is outside the traversing range but inside the traversing range inflated
by 5mm (field of view of the camera = 5mm), the PCB camera is moved to the nearest position and the
crosshairs are drawn excentric into the live image with an Offset in the direction of the component.
Otherwise an error message is displayed.
The functionality is supported on the following machines: S27 HM, HS50, HS60, HF, HF (as of A-001)
and HF/3.
4.2.1 Restrictions
On an S-27 HM machine it may be necessary to increase or decrease the y axis traversing range.
The functionality is not supported on S25 HM machines.
Software Version Description, Station Software 505.05 07/2008 Edition
4.3 Whispering of fiducials
As of this station software the "whispering of fiducials" (i.e. the forwarding of fiducial data) is available
for the line (WDTL). The function can be activated in the machine options under "Forwarding of board
ink spot data". For a detailed description, please refer to the Online Help system for the station
software. The requirements and restrictions are the same as described in the "
Whispering of ink spots"
section.
Note:
In the WDTL and WDTM of fiducials mode, the fiducial measurement is performed before the
ink spot measurement (automatically switched).
4.3.1 Requirements
The functionality requires SIPLACE Pro as of Version 5.0.
4.4 Integration of the "Repair placement of hoisted components"
Special Design
As of this software version it is possible to perform a repair placement for components that are still
attached to the nozzle (hoisted components) after a placement cycle. For this option, a component
sensor must be used (SIPLACE Pro requirement).
Components that are to be measured with the component sensor are not considered to be placed until
a component sensor measurement makes sure, that no components are attached to the nozzle after
placement trial. However, if components should still be attached to the nozzle, they will be rejected and
a repair placement will be performed later for the placement position concerned. The “3530 Warning:
Nozzle is deactivated“ error message is displayed.
The function can be activated or deactivated with the "Repair place component" button in the machine
options.
If the component cannot be rejected, the segment will be deactivated. Deactivated nozzles can
automatically be replaced, if the "Change deactivated nozzles" button ist activated in the machine
options.
If a job is changed, the deactivated nozzles are detected and as far as possible automatically replaced
or the "15520 Automatic nozzle change is not possible" error message is displayed.
21 of 150