00193794-11_VD_SSW 505.05_de en.pdf - 第56页

Software Version Description, Station Software 505.05 07/2008 Edition - Mapping There is no new mapping plate available with a width of 430 mm. This results in the following restrictions: If the machine zero point is mov…

Software Version Description, Station Software 505.05 07/2008 Edition

Add-on modules:

If add-on modules are installed within the travel range that prevent the fixed edge from being

moved (e.g. ceramic substrate centering), you cannot change the conveyor configuration by

means of "Adjust position of fixed edge" Æ "Standard width"/"Excess width".

- Dual conveyor:

Both tracks on the dual conveyor are treated in the same way. Individual widths are not set.

- Flexible dual conveyor:

Only the outer edge is adjusted on the flexible dual conveyor. The movable edges remain at the

edge.

- Excess-width conveyor:

If the stop is to be changed from right to left on an HS60 with a conveyor configured for excess

width, the stop has to be configured first, followed by the conveyor width.

- Subsequent actions:

After you change the conveyor configuration changed by means of "Adjust position of fixed

edge" Æ "Standard width"/"Excess width", you have to restart the machine and carry out

calibration. It is up to the operator to perform these subsequent actions.

In addition:

- Machines that support the "wide conveyor" feature:

The "wide conveyor" feature (changing of the conveyor configuration by means of "Adjust

position of fixed edge" Æ "Standard width"/"Excess width") is supported for machines in the HF

series and HS60 machine types. Machines of the type S25 HM / S27 HM, HS50 / HS50+ do not

support this feature.

- Feeders

Only S-tape feeders can be set up, since the widening of the placement area results in the

overlapping of the pickup and placement areas when other feeders are used. Linear feeders,

manual trays, MTCs and tray stack feeders, for example, are not among the standard feeders.

The hardware determines which feeders can be used.

One possibility for subsequent versions would be to modify the pick-up and placement areas so

that other feeder types could also be used with the help of the gantry synchronization feature.

55 of 150

Software Version Description, Station Software 505.05 07/2008 Edition

Mapping

There is no new mapping plate available with a width of 430 mm. This results in the following

restrictions:

If the machine zero point is moved outward, mapping is always carried out by means of

conveyor configuration ("Adjust position of fixed edge" Æ "Standard width"/"Excess width

HS60").

The maximum conveyor width in conjunction with the feature "flexible dual conveyor with

widened conveyor track" is 380 mm (not 430 mm) when "excess width HS60" is set for the

position of the fixed conveyor edge. This must be ensured by the conveyor firmware.

If the machine zero point is moved and "standard width" is set for the position of the fixed edge,

the maximum conveyor width in conjunction with the feature "flexible dual conveyor with

widened conveyor track" is only 330 mm (not 430 mm). This must be ensured by the conveyor

firmware.

If the machine zero point is moved outward, a mapping width of 508 mm is possible with the

single conveyor. The maximum conveyor widths must be ensured by the conveyor firmware.

- Programming system:

The "synchronous dual conveyor" feature is not supported in conjunction with the "wide

conveyor" feature, since the spacing of the PCB reference corners changes.

- Programming system/optimization:

Optimization does not take into account that the travel paths change with the feature.

5.33 Whispering of ink spots

In Version 505.03 the "whispering of ink spots" functionality (i.e. the forwarding of ink-spot data) is

available both for the line (WDTL) and in a machine with two processing areas (WDTM).

5.33.1 Requirements

- Whispering requires every station in the line to be equipped with PCB barcode readers.

- PCB barcode mode must be set both for the stations in the line and for the line itself in the

programming system.

- In whispering mode, the ink-spot recognition option must be activated on every station in every

processing area (PA).

56 of 150

Software Version Description, Station Software 505.05 07/2008 Edition

5.33.2 Requirements

- Ink spots are always whispered. That applies both to the machine (WDTM – Whispering down

the Machine) and to the line (WDTL – Whispering down the Line). The whispering of ink spots is

carried out incrementally.

- Subpanels and component fiducials are not whispered (either down the machine or down the

line).

- The machine options "PCB data transfer" (= WDTL) und "PCB transfer from PA 1" (= WDTM)

are no longer displayed as options that can be selected.

- Whispering of ink spots is also possible in connection with the "Long PCB" option.

- If PCBs are conveyed through a processing area without being processed (e.g. because a panel

is specified (Æ empty panel) or because of the incorrect orientation of the components, the

incremental whispering of ink spots is not interrupted.

5.33.3 Restrictions

- Whispering of ink spots is not possible in connection with the "Synchronous dual conveyor"

option.

- Whispering of ink spots is not possible in connection with the recovery placement feature.

- Machines for which "Transport through" is set in all processing areas interrupt the incremental

whispering of ink spots.

- The whispering of ink spots in mixed lines (platform 1 and platform 2 machines) is only possible

to a limited extent:

Permitted configuration of mixed lines 407.04 / 505.03

Whispering is not possible in lines with "productivity lift".

- In station-by-station downloading, all jobs must be specified with the same whisper mode.

57 of 150