DECAN_S2_Trouble(Eng_Ver4.2).pdf - 第176页
1-154 Advanced Chip Shooter DECAN S2 T roubleshooting Guide Set the lighting so that the boundary of lead and foot is vi sible. $ad10 Did not find the beginning of lead in the (%d)th lead group. [Problem] Lighting se…
1-153
System Messages of the MMI and Solutions
The ‘Auto Teah’ function is not supported for the components having missing pins.
[Solution]
Register manually for the components having missing pins.
$ad05 Lead group on one side shall be one for ‘Auto Teach’.
[Problem]
The ‘Auto Teach’ function is not supported for the component having more than two
lead groups on one side.
[Solution]
Register manually the component having more than two lead groups on one side.
$ad06 When performing “AutoTeach”, the number of parameters is different from that of
the lead group, and it cannot be one parameter.
[Problem]
An error occurred due to H/W problem or S/W problem.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ad07 Can not find the end of foot of the(%d)th lead group when performing ‘Auto Teach’
$ad08 Can not find the beginning of the foot of the(%d)th lead group when performing
‘Auto Teach’.
[Problem]
Lighting setup is inadequate.
[Solution]
Select the error occurred component in “Part” of the “PCB Edit” menu and check that
illumination is correctly setup in the “Profile Editor”.
Set the background of the component to look dark, and the lead and foot to look bright.
$ad09 Can not find the boundary of foot and lead in the(%d)th lead group when performing
‘Auto Teach’.
[Problem]
The boundary between the lead and foot is not visible when performing the ‘Auto
Teach’.
Lighting setup is inadequate.
[Solution]
Select the error occurred component in “Part” of the “PCB Edit” menu and check that
illumination is correctly setup in the “Profile Editor”.
1-154
Advanced Chip Shooter DECAN S2 Troubleshooting Guide
Set the lighting so that the boundary of lead and foot is visible.
$ad10 Did not find the beginning of lead in the (%d)th lead group.
[Problem]
Lighting setup is inadequate.
[Solution]
Select the error occurred component in “Part” of the “PCB Edit” menu and check that
illumination is correctly setup in the “Profile Editor”.
Set the background of the component to look dark, and the lead and foot to look bright.
$ad11 An error of different numbers for ascent edge (%d) and descent edge (%d) occurred
in the lead group %d during auto teaching.
[Problem]
An error occurred due to H/W problem or S/W problem.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ad12 An error in which the height (or width) of a component equals 1 pixel occurred during
auto teaching.
[Problem]
An error occurred due to H/W problem or S/W problem.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ad13 Failed in recognition because there is no bright pixel exceeding the threshold(%d)
value on the screen when performing ‘Auto Teach’.
[Problem]
Lighting is set up too dark.
[Solution]
Select the error occurred component in “Part” of the “PCB Edit” menu, and add clarity
to the shape of the component by changing the illumination setup in the “Profile
Editor”.
$ad14 The component is off the effective range when performing ‘Auto Teach’.
[Problem]
The component was so large that it covered the outline of the screen.
1-155
System Messages of the MMI and Solutions
The component was picked being offset and extended toward the edge of the screen.
Foreign matter except for the component looked bright.
[Solution]
Register manually if the size of the component is too large.
If the component is picked being offset, Check through SMVision window to
determine the pickup position of the corresponding component in the Feeder of the
“PCB Edit” menu.
Remove foreign matter if it looks brighter than the component.
$ad15 Failed in recognition because the number(%d) of recognized lead of the %d lead
group is less than four during ‘Auto Teach’.
[Problem]
The ‘Auto Teach’ function does not support the component having less than four
leads.
Lighting setup is inadequate.
[Solution]
Register manually the components having less than four leads.
Select the error occurred component in “Part” of the “PCB Edit” menu and check that
illumination is correctly setup in the “Profile Editor”.
$ad16 Failed to recognize the angle because the angle(%d) of the recognized component is
above ±20 when performing ‘Auto Teach’.
[Problem]
The pickup angle of the component shall be within ±20 degree when performing the
‘Auto Teach’.
[Solution]
Check the pickup status of the component, pick up at an angle close to 0 degree, and
retry.
$ad17 Failed to recognize because the number(%d, %d) of the recognized lead groups(%d,
%d) facing each other is different when performing ‘Auto Teach’.
[Problem]
Number of the leads of the lead group for which the ‘Auto Teach’ is performed is
different.
The “Auto Teach” supports CHIP-Rect, TR, TR2, BGA, SOP, SOP2, SOJ, SOJ2, QFP,
PLCC and FLIPCHIP only.
The component is defective when performing the ‘Auto Teach’.
Lighting is set up inadequate.