DECAN_S2_Trouble(Eng_Ver4.2).pdf - 第22页

Advanced Chip Shooter DECAN S2 T roubleshooting Guide xii About This Manual  Composition of this Manual The manual for this machine is comprised as follows.  Handbook  Operation Handbook Describes briefly a series of …

Preface

About virus protection

For the safe use of the machine, the machine system shall be maintained normally through

virus protection.

 Basic items to be observed for virus protection are as follows:

 Install the anti-virus program (TrusLine) provided by us so that any virus can be

treated by performing a virus check periodically. When installing the program,

contact our C/S or local agent.

 Run the anti-virus program and check for viruses without fail before starting the

machine and preparing production. Running the anti-virus program during

production may affect the performance of the machine.

 Update the anti-virus program engine periodically. Use a PC without a virus as an

update server when updating the anti-virus program engine for the machine

system.

For the corresponding PC, update the anti-virus program engine periodically

through the Internet and perform configuration in the ant-virus program to update

the anti-virus program engine of the machine by sharing the folder in which the

updated file is saved with the machine system.

 When loading a PCB file or saving it in the system using storage media including

USBs, perform an anti-virus check first on the corresponding storage media and

check for any problems.

 When using a shared folder in the machine system as necessary, set the password

for the shared folder without fail.

Advanced Chip Shooter DECAN S2 Troubleshooting Guide

xii

About This Manual

 Composition of this Manual

The manual for this machine is comprised as follows.

 Handbook

 Operation Handbook

Describes briefly a series of processes that is performed by the operator.

 Maintenance Handbook

Describes briefly basic points related to maintenance of the machine;

Preparation for maintenance, daily inspection, periodical inspection, cleaning

and lubrication method, definition of consumables including replacement time

and method.

 Administrator’s Guide

Describes the program for PCB production or various system setups related to the

machine;User’s account administration and authority setup, board definition,

component registration, feeding device setup, step programming, optimization,

production setup, teaching and placement test, machine calibration, system setup,

machine diagnosis, utility menu setup and production information management

 Troubleshooting Guide

Describes definition and the method used to take measures against the errors;

Describes definition and solution for error codes and the errors not defined

 Technical Reference

Provides part information for the maintenance and various technical drawings.

 Symbols other than safety marks used in this manual

The meanings of symbols used in this manual are as follows:

ReferenceReference indicates a part to be referred to.

Memo Describes useful information related to the text or definition of terms.

1-1

System Messages of the MMI and Solutions

Chapter1. System Messages of the MMI

and Solutions

1.1. Trouble Shooting Guide in general

If one of the errors to be explained below happens during the operation of machine, take

actions explained in the corrective action section. If such errors persist once these

measures have been taken, or if errors not mentioned in this manual occur, take the

following actions and contact our CS company or local agent.

 First, download the log file necessary for the corrective action and store it.

 For the errors related to machine operation, carry out homing of all axes, then take

corrective actions.

 If the problem persists, turn off the power, and restart after 10 seconds, and take

corrective actions.

 If the problem persists even after all the measures explained above have been taken,

send us the log file stored according to the first procedure and consult the C/S

company or the local agent for further actions.

If an abnormal S/W error or another error occurs, send the C/S company or the local agent

following files for faster problem solving.

 Work PCB file (A file whose extension is .pcb or .opt)

 Error log file (All the files in ‘C:\SmartSM\Log’ f'older)

 Machine calibration file (All the files in ‘C:\SmartSM\System’ folder)

Warning Referring to the machine status indication group of the MMI,

check the error level according to the error code. If the error

level indicates Emergency (EMER) or Freeze (FREEZE),

press the “STOP” button to turn off the buzzer first and then

press the “RESET” button to put the machine in idle state.

Measures can then be taken to rectify this problem.

If it is MPU_STOP, stop the machine normally and reboot it.

Adjusting a sensor or correcting an error while the machine

is in the ready status could cause injury. Release the

‘Ready’ without fail. Adjust the sensor and then take

corrective measures against the error while the machine is

stopped.