DECAN_S2_Trouble(Eng_Ver4.2).pdf - 第84页

1-62 Advanced Chip Shooter DECAN S2 T roubleshooting Guide  Although the docking cart was moved up/down, the Up/Down s ensor failed to detect the up/down move ment of the docking cart even after the designated time. [So…

1-61

System Messages of the MMI and Solutions

$0031 Front cart has been released at the position where XY is not safe. [EMER LEVEL]

$0033 Rear cart has been released when the cart cannot be released. [EMER LEVEL]

[Problem]

 When the docking cart is released abnormally.

[Solution]

 Turn off the Buzzer by pressing the “STOP” button.

 Switch the machine to “IDLE” mode by pressing the “RESET” button.

 Check the pneumatic pressure supplied to the docking cart cylinder.

 Check the movement of the solenoid for the corresponding cylinder.

 Supply power to the motor of the machine by pressing the “READY” button.

$0040 The mirror axis did not get out of the detection range of the home sensor.

[Problem]

 Even though the mirror axis is opened, it did not get out of the detection range of the

home sensor.

[Solution]

 Check the state of the mirror axis home sensor or the dog sensor connection state.

 Move the mirror axis to check if any change occurs in the state of the home sensor. If

no change occurs, check the connection state of the sensor, cable, etc.

 If there occurs any change in the state of the home sensor, check the connection state

of the cables for the axis board and driver.

 If the problem remains unsolved, contact our designated C/S company or local agent.

$0043 Failed to move up the front docking cart. [EMER LEVEL]

$0046 The front docking cart was not docked properly. [EMER LEVEL]

[Problem]

 The front docking cart is not clamped properly.

[Solution]

 Check the contact state of the docking cart and the state of sensors.

 If the problem remains unsolved, contact our designated C/S company or local agent.

$0048 Failed to move up the rear docking cart. [EMER LEVEL]

$0049 Failed to move down the rear docking cart. [EMER LEVEL]

[Problem]

1-62

Advanced Chip Shooter DECAN S2 Troubleshooting Guide

 Although the docking cart was moved up/down, the Up/Down sensor failed to detect

the up/down movement of the docking cart even after the designated time.

[Solution]

 Check if the docking cart contacts closely with the machine.

 Check the up/down movement state of the docking cart. If the docking cart interferes

with anything, remove it.

 Check the sensor operation by moving the docking cart up and down.

 If the problem remains unsolved, contact our designated C/S company or local agent.

$0051 The rear docking cart was not docked properly. [EMER LEVEL]

[Problem]

 The docking cart is not clamped properly.

[Solution]

 Take measures same as those against the error code “$0046”.

$0052 The front docking cart has already moved up or it was not docked properly. [EMER

LEVEL]

$0053 The rear docking cart has already moved up or it was not docked properly. [EMER

LEVEL]

[Problem]

 An attempt was made to move the docking cart up when it was already moved up.

[Solution]

 Check the contact state of the docking cart and the state of sensors.

 If the problem remains unsolved, contact our designated C/S company or local agent.

$0054 The front docking cart has not been moved up. [EMER LEVEL]

$0055 The rear docking cart has not been moved up . [EMER LEVEL]

[Problem]

 The docking cart has not been moved up before starting automatic production.

[Solution]

 Move the docking cart up and restart the automatic production.

 If an error occurs while it moves up, take proper measures by referring to the related

error code.

 If the problem remains unsolved, contact our designated C/S company or local agent.

1-63

System Messages of the MMI and Solutions

$0120 The feeder exchange button was pressed.. [NORMAL LEVEL]

$0805 Cannot operate the feeder since the Z-axis position is not safe . [EMER LEVEL]

[Problem]

 The Z-axis of all heads is not at the safe height before operating the feeders (including

tray feeder).

[Solution]

 When the Z-axis of some heads is lowered, perform homing of the Z-axis of the

corresponding head and attempt the planned operation.

 When feeders were operated after EMG occurred without performing the homing,

perform the homing first and then attempt the planned operation.

 If the problem remains unsolved, contact our designated C/S company or local agent.

$0915 The Y Interference detection sensor detected the approach of other gantries. [EMER

LEVEL]

[Problem]

 The Y interference detection sensor detected the approach of other gantries.

[Solution]

 The Y interference detection sensor detected the approach of other gantries.

 Check if the two approaching gantries were detected by the interference sensor.

 Check the operation status of the proximity sensor.

 Press the Stop button and Reset button in order to release the error state of the

machine.

 Perform homing of the entire machine to check if the homing is performed properly.

 Check the connection state of the servo system (axis boards, motor boards).

 The problem remaining unsolved may cause serious problems including collision of

the gantry with an internal frame, etc. Therefore, stop the machine immediately and

contact our designated C/S company or local agent

$0950 The teaching box is disabled at the front side. [WARNING LEVEL]

$0951 The teaching box is disabled at the rear side. [WARNING LEVEL]

$0952 The teaching box is connected to both front and rear sides . [WARNING LEVEL]

[Problem]

 The teaching box is connected to both operation panels.

[Solution]

 Remove the teaching box at one side for normal operation.

 It is presumed that an error occurred in the distribution board of the operation panel.

Check the operation state.