DECAN_S2_Trouble(Eng_Ver4.2).pdf - 第94页

1-72 Advanced Chip Shooter DECAN S2 T roubleshooting Guide $3055 Attempt was made to turn the belt wh ile already turning. [EMER LEVEL] $3059 An error occurred to the rail axis cont roller. [EMER LEVEL] [Problem]  A c o…

100%1 / 200
1-71
System Messages of the MMI and Solutions
Warning Please check the movement of the sensor and cylinder in
the ‘Diagnosis I/O’ of MMI.
As it is dangerous to check the sensor during the operation
of the equipment, be sure to check the equipment in stop
status (idle mode) after releasing “Ready”.
$3049 Failed to turn the edge fixer on. [EMER LEVEL]
[Problem]
The edge fixer does not turn on normally.
[Solution]
Take measures same as those against the error code "$3048”.
$304a Failed to turn the edge fixer off. [EMER LEVEL]
[Problem]
The edge fixer does not turn off normally..
[Solution]
Take measures same as those against the error code "$3048”.
$304e An error occurred to the belt controller. [EMER LEVEL]
[Problem]
The conveyor belt does not run normally.
[Solution]
Turn off the Buzzer by pressing the “STOP” button.
Switch the machine to “IDLE” mode by pressing the “RESET” button.
Supply power to the motor of the machine by pressing the “READY” button.
Drive the belt again.
$304f There is no response from the belt controller. [EMER LEVEL]
[Problem]
The conveyor belt does not run normally.
[Solution]
Take measures same as those against the error code "$304e”.
Check the state of the corresponding step control board and driver
1-72
Advanced Chip Shooter DECAN S2 Troubleshooting Guide
$3055 Attempt was made to turn the belt while already turning. [EMER LEVEL]
$3059 An error occurred to the rail axis controller. [EMER LEVEL]
[Problem]
A command that moves the conveyor was transmitted to the step control board, but an
error occurred.
[Solution]
Turn off the Buzzer by pressing the “STOP” button.
Switch the machine to “IDLE” mode by pressing the “RESET” button.
Check the state of the corresponding step control board and driver.
$305b Exceeded the conveyor width movement range. [EMER LEVEL]
[Problem]
Attempt was made to adjust the conveyor width exceeding the maximum or minimum
width.
[Solution]
Perform setup of the width adjustment according to the specification of the current
machine..
$3060 Attempt was made to adjust the conveyor width while the conveyor width was already
being adjusted.. [EMER LEVEL]
$3061 The conveyor needs to be homed. [EMER LEVEL]
[Problem]
When operating the conveyor that was not homed.
[Solution]
Turn off the Buzzer by pressing the “STOP” button.
Switch the machine to “IDLE” mode by pressing the “RESET” button.
Supply power to the motor of the machine by pressing the “READY” button.
Home all axes related to conveyor and perform operation related to conveyor.
$3067 Cannot begin production since the conveyor rail width does not match with the PCB
width. [EMER LEVEL]
[Problem]
There is difference between conveyor stations.
[Solution]
Turn off the Buzzer by pressing the “STOP” button.
Switch the machine to “IDLE” mode by pressing the “RESET” button.
Supply power to the motor of the machine by pressing the “READY” button.
1-73
System Messages of the MMI and Solutions
Make the width of all conveyor stations identical.
$306a Timeout occurred while changing conveyor width. [EMER LEVEL]
[Problem]
The conveyor width failed to be adjusted as designated within designated time while
changing conveyor width.
[Solution]
Turn off the Buzzer by pressing the “STOP” button.
Switch the machine to “IDLE” mode by pressing the “RESET” button.
Check if there is any mechanical interference while changing conveyor width.
Check the operation state of the step control board and PB driver related to the width
adjustment of the corresponding conveyor
$306b Timeout occurred while the conveyor is homed. [EMER LEVEL]
[Problem]
The conveyor width failed to be adjusted as designated within designated time while
homing the rail axis.
[Solution]
Take measures same as those against the error code "$306a”.
$306c An error occurred to the shuttle controller. [EMER LEVEL]
[Problem]
The machine operated incorrectly to the command related to the shuttle.
[Solution]
Turn off the Buzzer by pressing the “STOP” button.
Switch the machine to “IDLE” mode by pressing the “RESET” button.
Check if there is mechanical interference related to the shuttle movement.
Check the operation state of the step control board and PB driver related to the shuttle
movement.
$306e The shuttle moved out of its movement range. [EMER LEVEL]
[Problem]
The shuttle moved out of its mechanical movement range..
[Solution]
Turn off the Buzzer by pressing the “STOP” button.
Switch the machine to “IDLE” mode by pressing the “RESET” button.
Supply power to the motor of the machine by pressing the “READY” button.