DECAN_S1_Troubleshooting_Guide(Eng_Ver1.3)_Print_Web.pdf - 第174页

1-150 Next Generation, Multi-Functional Plac er DECAN S1 Troubleshooting Guide  The nozzle is contaminated with foreign matter . [Solution]  Select the error occurred comp onent in “Part” of the “P CB Edit” menu, and c…

100%1 / 204
1-149
System Messages of the MMI and Solutions
Perform [Solution] in $aa1f.
$ab29 Error occurred while inspecting leads.
[Problem]
The component was not picked up.
The lead of the component is bent too much.
Incorrect input of the lead information.
[Solution]
Perform [Solution] in $aa1f.
$ab2b Angle of the component has deviated from the reference value.
[Problem]
Angle of the component has been rotated too much when picking up the component.
[Solution]
If a component is not picked up, assign the component pickup position again at the
PCB edit feeder of the MMI. Through the SMVision window, check the pickup
position of the corresponding component in “Feeder” of the “PCB Edit” menu.
Check if selection of the nozzle is correct.
$ac00 Incorrect angle number has been transmitted from the VME.
[Problem]
An incorrect angle method has been transmitted from the VME.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ac02 Input of incorrect parameter.
[Problem]
Input of the incorrect value of the component parameter.
[Solution]
Check the parameter of the corresponding component on the ‘Part’ of the PCB Edit
menu.
$ac07 The recognized width of the component was different from the reference value.
[Problem]
Incorrect input of the ‘Body X of the component.
The tolerance for H and L of the component was set too low.
1-150
Next Generation, Multi-Functional Placer DECAN S1 Troubleshooting Guide
The nozzle is contaminated with foreign matter.
[Solution]
Select the error occurred component in “Part” of the “PCB Edit” menu, and check if
the ‘Body X’ at ‘Profile Editor’ has been correctly input.
Select the error occurred component in “Part” of the “PCB Edit” menu, and enter 30%
as the tolerance for each of H and L in the ‘Profile Editor’.
Remove the foreign matter, if any.
Please refer to the [Solution] in $a635.
$ac08 The recognized height of the component was different from the reference value.
[Problem]
Incorrect input of ‘Body Y’ of the component.
oo low setup of the tolerances for H and L of the components.
Foreign matter is in the nozzle.
[Solution]
Perform [Solution] in $ac07.
$ac09 Internal function Error(CenterCorrection).
[Problem]
An error occurred during component recognition.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ac0a Undefined algorithm.
[Problem]
An incorrect result has been received from the VME.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ac0b Internal function Error(LineFitting 1).
$ac0c Internal function Error(LineFitting 2).
$ac0d Internal function Error(LineFitting 3).
$ac0e Internal function Error(LineFitting 4).
$ac0f Internal function Error(LineFitting 5).
[Problem]
1-151
System Messages of the MMI and Solutions
An error occurred during component recognition.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ac10 The length of lead is too long to recognize.
[Problem]
Inputted sum of upper leads and lower leads is greater than the ‘Body Y’ of the
component.
[Solution]
Input smaller value for ‘Y’ if the ‘L’ value, sum of upper lead and lower lead, is larger
than ‘Body Y’ of the component.
$ac11 The component is set too small or the lead length is set too long.
[Problem]
The inputted lead length(L) of the component is too long.
[Solution]
Set up the lead length(L) of the component to be smaller than the existing value.
$ac12 The width of the component has been recognized to be smaller than the reference
value.
[Problem]
An error occurred during component recognition.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ac13 The width of the component has been recognized to be larger than the reference value.
[Problem]
An error occurred during component recognition.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ac14 The angle of the component has deviated from the reference value.
[Problem]
The Angle of the component has been rotated too much when picking up the
component.