DECAN_S1_Troubleshooting_Guide(Eng_Ver1.3)_Print_Web.pdf - 第30页

1-6 Next Generation, Multi-Functional Plac er DECAN S1 Troubleshooting Guide Camera recognition timeout error / V ision processing timeout error .Defective vision board .Defective V ision board connection E0206 Fiducial …

1-5

System Messages of the MMI and Solutions

 When parts are picked up properly - Part recognition error [Refer to Section

1.2.1.2]

Cause Description Remarks

Failed to output the

images taken by the

camera

.Defective fly camera or fix camera

.Defective fly camera I/F cable or defective

stage CAM 1 and 2 cables and connections

.Defective Fly Camera PW Sync Exit Cable

and connection

.Defective vision board

.Defective vision I/F board

.Defective camera I/O board (total

destruction of internal chips by fire)

.Defective power supply

.Defective vision board IF cable and

connection

E0200

Damaged image from

the camera

Unclear image from the

camera

.Defective Fly Cam Sig Ext cable or Fix Cam

signal cable and connection

.Defective camera focus

.Contaminated camera lens and foreign

material on the lens

.Camera dip switch setup error

E0201

Vision processing

timeout /

Failed to recognize the

vision board

.Defective Vision board connection

.Defective SBC

.Defective vision board

.Defective backplane board

.Damaged vision board driver file due to

infection by virus

E0202

Damage to the mirror .Scratch to the mirror

.Damaged mirror

.Mirror contaminated with foreign material

E0203

Part data registration

error

.Part recognition data registration error

.Recognition parameter setup error

.Illumination setup error

E0204

Defective part The part size is different from that of the

recognition data of the registered part due to

a defective part

E0205

1-6

Next Generation, Multi-Functional Placer DECAN S1 Troubleshooting Guide

Camera recognition

timeout error / Vision

processing timeout

error

.Defective vision board

.Defective Vision board connection

E0206

Fiducial camera noise

(Occurrence of

distorted image, half

image, overlapped

image, etc.)

.Defective Fiducial Camera cable

connection

.Defective fiducial camera

.Defective vision board I/F

E0207

Defective camera

assembling

The camera recognition area is not located

at the part center but slightly offset in the X-

axis or Y-axis direction

E0208

The image from the

camera is dark

Abnormal illumination

brightness

.Defective camera illumination board

(Defective outer illumination board)

.Defective head illumination board

.The illumination LEDs turn on and off

repeatedly due to defective contact of the

cable related to the lighting

.Light mapping error

E0209

Contaminated nozzle E0211

Defective recognition

of 'Ref' mark on the

head

Contaminated 'Ref' mark on the head E0212

Cause Description Remarks

1-7

System Messages of the MMI and Solutions

1.2.1.1. Part Non-pickup Error

E0000 Incorrect installation of tape reel in the tape feeder

[Cause]

 Sprocket teeth of the tape feeder are not engaged correctly into the tape holes.

[Measures]

 Engage the sprocket teeth of the tape feeder into the tape holes correctly.

E0010 A part is flipped over or stands on an edge

[Cause]

1) When peeling the upper cover tape manually, parts are taken out being attached with

the vinyl Emboss tape reel is used for an 8mm and 4 pitch feeder that uses paper tape

reel

2) Emboss tape reel is used for an 8mm 4 pitch feeder that uses a paper tape reel.

[Measures]

1) Replace the tape reel.

2) For an emboss tape reel, use an emboss tape feeder.

E0011 A part is stuck to the tape guide (only for 8mm feeder)

[Cause]

 Static electricity occurred to a part or a part is stuck to the tape guide since it was

magnetized

[Measures]

 Contact our designated C/S company or local agent. (Replace the tape guide)

For further details, refer to the following documents:

Technical Reference : Tape Feeder

E0012 A part is flipped over or stands on an edge due to deformation of the tape guide and

shutter

[Cause]

1) The tape guide does not move smoothly or it is deformed due to impact

2) When supplying parts manually, a part interferes with the shutter

[Measures]

1) Contact our designated C/S company or local agent. (Replace the tape guide)

2) Contact our designated C/S company or local agent. (Replace the shutter)