DECAN_S1_Troubleshooting_Guide(Eng_Ver1.3)_Print_Web.pdf - 第82页
1-58 Next Generation, Multi-Functional Plac er DECAN S1 Troubleshooting Guide 1.4.2. Switch and machine safety related errors [$0001~$0fff] Warning Adjusting a sensor or corre cting an error while t he machine is in the …
1-57
System Messages of the MMI and Solutions
1.4. Error Code
1.4.1. Classification of Error Codes
Error code Details Note
$0001~$0fff Switch, Machine safety related errors
$1000~$1fff Axis related errors (Includes limit sensor related errors)
$2000~$2fff IO (Sensor input after solenoid operation) related errors Not Used
$3000~$3fff Conveyor related errors (Includes BUT, Hole Fixer, Edge
Fixer)
$4000~$4fff machine operation sequence errors
$5000~$50ff Common Error Related to Feeding Device and Production.
$5100~$51ff Tape Feeder related errors
$5200~$52ff Stick Feeder related errors
$5300~$53ff Tray Feeder related errors
$5400~$54ff Reserved
$5500~$55ff Tray Feeder communication related errors
$5600~$57ff Reserved
$5800~$58ff Component related errors (component Recognition, Vacuum
related error so on)
Not Used
$5900~$5fff Reserved
$6000~$65ff ANC related errors
$6600~$66ff 3MO related errors Not Used
$6700~$67ff Accessory device related errors
$7000~$8fff Reserved
$9000~$9fff Vision related errors in MMI
$a000~$afff Vision related errors in VME
$b000~$bfff Software debug related errors
$c000~$cfff Motion control related errors
$d000~$d2ff DPRAM communication related errors
$e000~$efff Internal data related errors (Board, MPU Init related Error,
Factory, System DB Error)
$f000~$ffff Internal data related errors (Board, MPU Init related Error,
Factory, System DB Error)
1-58
Next Generation, Multi-Functional Placer DECAN S1 Troubleshooting Guide
1.4.2. Switch and machine safety related errors [$0001~$0fff]
Warning Adjusting a sensor or correcting an error while the machine
is in the ready status could cause injury. Be sure to adjust a
sensor or correct an error after releasing the ready status
and while the machine is in the stop status(idle mode).
Warning Restarting the equipment without removing the cause of
emergency stop could cause damage to the equipment or
injury. Be sure to remove the cause of emergency stop
before restarting the equipment.
$0002 The emergency switch in the front of equipment is pressed. [EMER LEVEL]
$0003 Rear emergency switch is pressed. [EMER LEVEL]
[Problem]
The emergency switch in the front or the rear of the equipment is pressed.
[Solution]
Release the pressed “EMG” switch by turning it clockwise.
Turn off the Buzzer by pressing the “STOP” button.
Determine the cause of the emergency stop and eliminate it.
Switch the machine to “IDLE” mode by pressing the “RESET” button.
Supply power to the motor of the machine by pressing the “READY” button
If necessary, perform ‘Ready-To-Origin’.
1-59
System Messages of the MMI and Solutions
$0004 Motor free switch in the teaching box is pressed. [EMER LEVEL]
[Problem]
The motor free switch in the teaching box is pressed.
[Solution]
Turn off the Buzzer by pressing the “STOP” button.
Switch the machine to “IDLE” mode by pressing the “RESET” button.
Supply power to the motor of the machine by pressing the “READY” button.
If necessary, perform ‘Ready-To-Origin’.
$0010 The front feeder unlock sensor detected the tape feeder. [EMER LEVEL]
[Problem]
The front feeder unlock sensor detected the tape feeder
[Solution]
Check the installation status of the feeder installed in the front feeder slot.
When an object is detected by the unlock sensor, remove it.
If an object is not detected by the unlock sensor, check the state of the feeder cover. If
it is opened, close the cover and install the feeder.
Remove other foreign materials.
Click the “READY” button to supply power to the motor of the machine.
Check the sensor or associated wiring. If it has a problem, contact our designated C/S
company or local agent.
$0011 The rear feeder unlock detected the tape feeder. [EMER LEVEL]
[Problem]
The rear feeder lift-off sensor detected the lift-off of the feeder.