00198000-02_VD_709.1_DE_EN.pdf - 第44页
Station Software 709.1 / Version Descript ion Ausgabe 05/2016 E dition 44 Conveyor Carrier X – No travel range ch eck. – No pickup simulati on. – The Conveyor Ca rrier X uses one trac k on an X - table v irtually. If the…
Station Software 709.1 / Version Description Ausgabe 05/2016 Edition
43
Twin VHF placement head
– Supported on the SX1/SX2 V2 placement machine (with a higher positioned gantry) only.
– No fast gantry exchange possible.
– Must not be used together with the VHF P&P on one machine.
SIPLACE JTF-S
Supported on the SX1/SX2 V2 and SIPLACE X-series S placement machines only.
SIPLACE JTF-M
– Supported on the SX1/SX2 V2, X4i S micron and SIPLACE X-series S placement machines
only.
– On the SX1/SX2 V2 placement machine no tape feeder can be placed on the location beside
the JTF-M because no empty tape channel is available.
SIPLACE Wafer Systems
– Supported on the CA-series placement machines only.
– A specific table is required.
External virtual ink spot handling
– Only possible for stations with station software from version 707.0 and SIPLACE Pro from
version 11.1.
– Physical and virtual ink spots must not be mixed.
– The board must not contain any active ink spots.
Software installation on older placement machines
During the station software installation on older X-series or X S-series placement machines that are
equipped with a CPP placement head and an MTC at location 2, a message is displayed that the
travel range has to be remeasured.
This occurs once to initialize the buffer monitoring. Thereafter, it will be checked if a retrofit has
been performed that requires a recalibration of the travel range.
CPP / Twin Head placement heads on SIPLACE CA series
– Stationary cameras may be installed on location 1 and 3 only.
– Twin Head may be installed on location 3 only.
– The CPP placement head is only supported in the high position on SIPLACE Wafer Systems.
Measuring and changing the component height measured by the component sensor at the
station
– Only for placement heads that are equipped with a component sensor.
– Only for nozzle and component combinations in which the component height is supposed to be
measured with the component sensor.
– The component sensor will not perform any measurement if the component height
measurement is omitted due to SIPLACE Pro rules.
Station Software 709.1 / Version Description Ausgabe 05/2016 Edition
44
Conveyor Carrier X
– No travel range check.
– No pickup simulation.
– The Conveyor Carrier X uses one track on an X-table virtually. If the real table should be
completely occupied, the operator might have to remove a feeder from the table to create place
for the virtual feeder.
– No I-Placement mode.
– The SIPLACE Pro Optimizer does not consider the time it takes to fill up a tray with
components and change it.
Individual barcode fiducials
– Barcode fiducials on the component underside are not supported because in this case the
barcode is read before the component is picked up.
SIPLACE TX-Serie
– Smart Pin Support is not supported.
– 3D-Coplan option is not supported.
– Restricted travel range for Twin Head:
The right segment cannot reach 3 tracks on the left side of the table,
the left segment cannot reach 3 tracks on the right side of the table.
– Restricted travel range for C&P20 P placement head:
Tracks 1-2 cannot be reached on location 1.
Heavy Board mode per board side
– No barcode mode possible.
Self-healing fiducial recognition
– Increasing the search area will only have an impact on geometric fiducials and not on fiducial
pattern.
– The second measurement will not be executed if the tolerance of a fiducial position is restricted
by the "Limited Tolerances" value in SIPLACE Pro.
Virtual keyboard
Cannot be used in the following cases:
– Changing the assignment of activity level to a button (right mouse key)
– During operating system installation as well as during any other software installation requiring
operating system administrator login.
Independent Placement – 2-in-1 mode
Not applicable for single conveyor, synchronous mode, alternating placement or machines
equipped with Smart Pin Support.
Station Software 709.1 / Version Description Ausgabe 05/2016 Edition
45
Verifying camera connections
– No support for checking 3D Coplan sensors.
Conveyor motor verification
No support on X-series conveyors.