_414214_AVK3 服务手册.pdf - 第27页

2.1 Installation Procedure SERVICE MANUAL A VK3 2.1−2 D77SEC−1 1−040−A0 2.1.2 Leveling Machine Leveling machine 1. Set machine main body accurately on the reference points. 2. Remove fixtures (for transportation) from X,…

2.1 Installation Procedure

SERVICE MANUAL

AVK3

2.1−1

D77SEC−11−040−A0

2.1 Installation Procedure

D77SEC−11−040−A0

Sentence No.

2.1.1 Installation Position

Installation position

1. Decide the installation position of machines from layout drawing (CAD drawing, etc.).

2. Mark the reference points of each machine on the floor with a marker pen, etc.

=NOTE=

In most cases, the machine front corners are used as reference points.

AVK3

JVK3B

BSF−V

C−CON

MBS

RHSG

C−CON

Reference points Reference points Reference points

*C−CON are connection conveyors which stand between machines.

3. Install the main body of each machine temporarily at reference points. (except for C-CON,

etc.)

4. The installation should start from the heaviest machine (A VK3).

AVK3

Reference points

5. Install the AVK3 main body accurately on reference points.

6. Decide the height from the floor to the transfer belt surface.

=Specification=

Height : 915±5mm

7. Adjust t he machine level (roughly).

8. Install other machines temporarily following the same procedure.

9. Install accessory conveyors such as C-CON, etc..

10. Raise the loader and unloader to the upper limit and adjust the clearance between the rails.

=Specification=

Clearance : 5±2mm

=NOTE=

If approx. 6mm cannot be provided between rails, move the machine.

11. Decide the height from the floor to the transfer belt surface.

=NOTE=

Depending on floor surface, there are times when transfer height can not reach

915mm.

12. Adjust the level between rails (front/rear, up/down directions).

2.1 Installation Procedure

SERVICE MANUAL

AVK3

2.1−2

D77SEC−11−040−A0

2.1.2 Leveling Machine

Leveling machine

1. Set machine main body accurately on the reference points.

2. Remove fixtures (for transportation) from X, Y, Z axes, etc.

Left feeder carriage

XY table

Z axis fixtures (2 pcs.)

XY axis fixture (1 pc.)

Right feeder carriage

=NOTE=

Make sure that feeder carriage sensor dogs do not interfere with the feeder carriage

sensors.

3. The machine main body is secured by 4 legs. Other legs are allowed to float.

DOWN

1 Rotation:3.5mm

Adjust bolt

4. Adjust the 4 legs and decide height from floor to transfer belt surface.

=Specification=

Height : 915±5mm

5. Set the level on the abraded face of XY table, adjust 4 legs to level the machine, and tighten

with locknuts. Place the levels in the designated positions on the machine (use 2 levels).

=NOTE=

Check that the levels are calibrated.

6. Adjust all other legs, and make sure the machine is still leveled (for AVK3, 8 − 4 = 4 legs).

7. Tighten all legs with locknuts and make sure the machine is still leveled. (check that there

are no floating legs).

2.1 Installation Procedure

SERVICE MANUAL

AVK3

2.1−3

D77SEC−11−040−A0

2.1.3 Accessories, Power Supply, Air Connections

Attachments

Accessories

1. Attach accessories (such as dust collector and signal tower) to the specified positions.

Air connections

1. Attach the primary side air tubing to the machine body and check the pneumatic pressure.

=Specification=

Air pressure: 0.5 MPa

=NOTE=

Remove oil or dirt from inside of the air tubing before connecting it.

Connection of primary side power supply

1. Check the voltage of primary side 3−phase power supply with the tester. (Electric power dis-

tribution on the factory side)

2. Check that the voltage of the tap connected to the built−in transformer is the same as the

factory power voltage.

3. If not, change the connection of built−in transformer. ........U, V, W

[EX.] Primary power supply of the factory: 380 V (Right terminal stand)

Move the wire connected to 200 V to the terminal of 380 V.

220V

200V

380V

400V

420V 480V

200V

・・・・

4. Connect primary 3−phase power supply on the factory side to main switch of the machine

and recheck the voltage with the tester

5. Turn ON the main switch and check the secondary side voltage of the built−in transformer

with the tester.

=Specification=

Voltage: AC200V±10V or below (3−phase)

Voltage: AC100V±5V or below

6. When the dust collector and other equipment are driven by 3−phase 200V power supply,

check the rotational direction of the dust collector with the main breaker [ON], machine pow-

er [ON] and ”SERVO MOTOR” on the main control panel [OFF].

If the rotational direction is not correct, change the phase of 3−phase power supply (Change

R−phase for V−phase.).