_414214_AVK3 服务手册.pdf - 第44页
4.1 Adjustment Check List SERVICE MANUAL A VK3 4.1−1 D77SEC−83−010−A0 4.1 Adjustment Check List D77SEC−83−010−A0 Sentence No. No. Adjustment Item Check Refer- ence T ransformer V oltage AC 100V T rans f ormer V o lt age …
SERVICE MANUAL
AVK3
4.0−2
D77SEC−83−000−A0
•
Each section has the procedure for performing maintenance as
described below.
The maintenance of the current page is represented by a bold frame.
The left frame shows the maintenance that must be done before
performing this maintenance, and the right frame shows the next
maintenance to be done.
Always follow the sequence when performing maintenance.
=NOTE=
Indication of related work in sequence.
=NOTE=
Indication of unrelated and some related work (independent).
4.1 Adjustment Check List
SERVICE MANUAL
AVK3
4.1−1
D77SEC−83−010−A0
4.1 Adjustment Check List
D77SEC−83−010−A0
Sentence No.
No. Adjustment Item Check
Refer-
ence
T
ransformer
V
oltage
AC 100V
T
rans
f
ormer
V
o
lt
age
AC 200V
Connector looseness
+5.00 to +5.25V
P783
+12.00 to +12.60V
Electrical
P783
main controller
Voltage
−12.00 to −12.60V
1.
El
ectr
i
ca
l
control sys-
tem
+15.00 to +15.75V
t
em
−15.00V to −15.75V
AC servo motor drivers Connector looseness
Power
supplier
Volta
g
e
5.1 to 5.6V
P
ower supp
li
er
V
oltage
(internal)
23.5 to 25.5V
Cooling
fan
Motor Normal rotation
C
oo
li
ng
f
an
Filter Clogging, dirt
Pneumatic
0.5MPa
Pneumatic
Main
regulator
P
neuma
ti
c
pressure
Stability during opera-
tion
2.
P
neumat
i
c
pressure con-
trol system
M
a
i
n regu
l
a
t
or
Pressure
switch
0.4MPa
Filter clogging, sediments in bowl
Tubing Wearing, damage, connection looseness
4.1 Adjustment Check List
SERVICE MANUAL
AVK3
4.1−2
D77SEC−83−010−A0
No.
Adjustment Item Check
Refer-
ence
3. PCB transfer
Transfer pin tra-
verse position
adjustment
Insertion amount
when putting the
transfer pin into
PCB hole
2mm to 3mm
X
axis
(+) limit +283.00 mm
4
XY table
overlimit
posi
X
ax
i
s
(−) limit −328.00 mm
Ch.4.
/
4
.
over
li
m
it
pos
i
-
tion
Y
axis
(+) limit +23.00 mm
Ch
.
4
.
/
4.4
Y
ax
i
s
(−) limit −386.00 mm
Head
θH
(Since θ correc-
tion operates to
limit
sensor
until
From origin on
90° (−) side
−9.5°
to before me-
chanical end
5
θ axis safety
limit
li
m
i
t sensor unt
il
±4°, set limit
sensor comes
[ON] when head
rotates over 4°.)
From 270° (+)
side
185°
to before me-
chanical end
5
.
li
m
it
Anvil
θA
(Since θ correc-
tion operates to
limit
sensor
until
From origin on (−)
side
−4.16°
to before me-
chanical end
li
m
i
t sensor unt
il
±4°, set limit
sensor comes
[ON] when anvil
rotates over 4°.)
From 90° (+) side
94.16°
to before me-
chanical end
From origin on (−)
side
−0.45 to −0.50mm
6. V axis overlimit
From 4mm on (+)
side
4.00mm to 5.5mm
to before me-
chanical end
7.
Z axis overli-
mit
When offset
data is 0
ZL (+) side
1820.5 to
1821.5mm