_414214_AVK3 服务手册.pdf - 第29页
2.1 Installation Procedure SERVICE MANUAL A VK3 2.1−4 D77SEC−1 1−040−A0 =NOTE= Make sure that the main breaker at the primary side is turned [OFF] when changing the phase of 3−phase power supply .
2.1 Installation Procedure
SERVICE MANUAL
AVK3
2.1−3
D77SEC−11−040−A0
2.1.3 Accessories, Power Supply, Air Connections
Attachments
Accessories
1. Attach accessories (such as dust collector and signal tower) to the specified positions.
Air connections
1. Attach the primary side air tubing to the machine body and check the pneumatic pressure.
=Specification=
Air pressure: 0.5 MPa
=NOTE=
Remove oil or dirt from inside of the air tubing before connecting it.
Connection of primary side power supply
1. Check the voltage of primary side 3−phase power supply with the tester. (Electric power dis-
tribution on the factory side)
2. Check that the voltage of the tap connected to the built−in transformer is the same as the
factory power voltage.
3. If not, change the connection of built−in transformer. ........U, V, W
[EX.] Primary power supply of the factory: 380 V (Right terminal stand)
Move the wire connected to 200 V to the terminal of 380 V.
U
U
220V
200V
380V
400V
420V 480V
V
200V
UU
U
U
W
200V
W
・・・・
・・・・
V
U
4. Connect primary 3−phase power supply on the factory side to main switch of the machine
and recheck the voltage with the tester
5. Turn ON the main switch and check the secondary side voltage of the built−in transformer
with the tester.
=Specification=
Voltage: AC200V±10V or below (3−phase)
Voltage: AC100V±5V or below
6. When the dust collector and other equipment are driven by 3−phase 200V power supply,
check the rotational direction of the dust collector with the main breaker [ON], machine pow-
er [ON] and ”SERVO MOTOR” on the main control panel [OFF].
If the rotational direction is not correct, change the phase of 3−phase power supply (Change
R−phase for V−phase.).
2.1 Installation Procedure
SERVICE MANUAL
AVK3
2.1−4
D77SEC−11−040−A0
=NOTE=
Make sure that the main breaker at the primary side is turned [OFF] when changing
the phase of 3−phase power supply.
2.1 Installation Procedure
SERVICE MANUAL
AVK3
2.1−5
D77SEC−11−040−A0
2.1.4 Safety Check for Factory Power Connections
Power wire check
Before supplying the power from the factory, visually check that the wire insulating sheath has
no damage nor degradation (crack, flaw and others).
Measurement of insulation resistance of the machine
Measure the insulation performance (insulation resistance) of the machine by following the
procedure shown below before connecting the factory power and make sure that it is 5 MΩ or
more.
1. Prepare a measuring instrument of insulation resistance tester which has the capacity of
DC500 V (common name: megger).
2. Make measuring terminal of insulation resistance tester have short circuit and make sure
that it is 0 Ω.
3. Turn ON the machine breaker, the external transformer breaker, the machine power switch,
the external transformer power switch and others.
4. Measure the insulation resistance between the machine power wire and the ground wire (PE
wire).
Insulation resistance tester
(Megger)
T
The terminals R, S and T
should be connected.
S
PE
R
Machine
=NOTE=
When the voltage regulator is connected between the machine and factory power,
measure the insulation performance of voltage regulator in the same way as the ma-
chine.
When the insulation performance is out of the criteria
1. Turn OFF the switch which is the farthest from the power side and check the change of the
insulation resistance.
2. Point out the position where the insulation resistance has a big change and check unit/wiring
in detail. Repair the wire if there are some faults.
3. When the problem persists even after re−wiring, component/unit may be defective. Ex-
change or repair the component/unit.
Checks after factory power connection
1. Tell the customers to ask the electrical facility specialist (maintenance provider), who have a
contract with the customers, to measure the insulation performance.