Horizon UserManualV6.pdf - 第175页

ERROR MESSAGE LISTING Error Message Interpretation Alignment Out of Range This indicates that the actuator positions required to achieve a satisfactory alignment are not attainable. Alignment Close to Limit/Out of Range …

ERROR RECOVERY

When an error message is displayed the following options maybe available to

recover the machine:

Abort Pressing this option re-initializes the entire printer, ejecting any product that may

be in the printer and returning to the main control page.

Retry Selecting this option re-checks the error condition and if clear continues the print

cycle.

Recover Pressing this option attempts to continue with any cycle that is in operation. This

function sets modules (paste dispenser, print carriage, etc.) to their home

position and ejects the board that is currently in the printer without re-initializing

the machine. This option should be the first to be operated if there is an error

reported.

Diagnostics This option enables the diagnostics to be entered immediately, normally by a

technician, for more in-depth investigation of the problem.

Open Cover This option allows the operator to select Change Screen to gain access to the

tooling area of the machine.

Continue When this option is available, selecting the continue key clears the error message

and continue with the cycle that is in operation.

Fiducial Setup When this option is available, selecting the Fiducial Setup key allows the user to

relearn the reported ‘Not Found’ fiducial.

Auto Search When this option is available, selecting the Auto Search key instigates a search

within the selected window size to locate the ‘Not Found’ fiducial.

Search Step When this option is available, selecting the Search Step key moves the camera

the first step in a search procedure designed to locate the ‘Not Found’ fiducial.

Further selection of the key moves the camera to the second step etc. Once the

fiducial is visible in the region of interest, the Retry key can be selected to

capture the fiducial.

Search Reset When this option is available, selecting the Search Reset key returns the camera

to its original position, before the Search Step key was selected. This is the

position from which the ‘Not Found’ fiducial was reported.

4.2 User Manual Software Version 6

ERROR MESSAGES

ERROR RECOVERY

ERROR MESSAGE LISTING

Error Message Interpretation

Alignment Out of Range This indicates that the actuator positions required to achieve

a satisfactory alignment are not attainable.

Alignment Close to

Limit/Out of Range

Actuator limit exceeded.

AutoFlex Timed Out This error reports that with AutoFlex tooling on high power

and the tooling pins up, the process time of 5 minutes has

been exceeded. When this message is displayed the power

is also switched to low.

Board Detected At Board

Stop, Print Terminated.

With the machine running in any mode, this error reports

that the board stop sensor has been activated out of

sequence.

Possible causes are:

Board already loaded into the machine.

Sensor is detecting tooling.

Sensor is faulty.

Board Fiducial Not Found This error reports that the vision system has been unable to

locate the board fiducial.

Board Not Over Input

Sensor

This error reports a machine has started without a board on

the rails. The user has ignored the message to place a board

on the rails and selects continue on the machine.

Board On Rails, Remove

and Continue

This error reports that a board has been sensed on the rails

during one of the following operations:

Initialization

Loading a new board file

Entering the rail system in diagnostics.

Board Stop Not Lowered This error reports that the board stop is up and has not

lowered within the time-out period of 3 seconds. The

possible causes are: Board stop sensor - enter Diagnostics

and check the sensor changes state.

Air pressure failure to the board stop.

Board Stop Not Retracted This error reports that the board stop is down and has not

retracted within the time-out period of 3 seconds. A

possible cause is:

Board stop sensor - enter Diagnostics, Digital Inputs and

check the sensor changes state.

Board Stop Stuck This error reports that the board stop, which is housed in

the camera assembly has failed to lower or retract.

Board Stuck in Rails This error reports that the board has failed to either reach

the board stop or exit the machine after being printed.

Camera X Axis Error This error reports that the camera carriage has failed to

reach its home position in the X axis.

Camera Y Axis Error This error reports that the camera carriage has failed to

reach its home position in the Y axis.

Command Timed Out

(Belt Motors)

This error reports if a board on the belt fails to move over

the board at left/right sensor within the time period.

Possible causes are:

Home sensor fault, if occurring during initialization.

Motor fault, if occurring during initialization.

Motor not running.

NextMove card faulty.

Software Version 6 User Manual 4.3

ERROR MESSAGES

ERROR MESSAGE LISTING

Error Message Interpretation

Command Timed Out

(Camera Axes)

This error reports that the camera has failed to move to the

demanded position within the time period. This error

applies to both the X and Y camera axis. Possible causes

are:

Home sensor fault, if occurring during initialization.

Motor fault, if occurring during initialization.

Motor not running.

NextMove card faulty.

Command Timed Out

(Paste Dispense Carriage)

This error reports that the paste dispense carriage has failed

to move to the demanded position within the time period.

Possible causes are:

Home sensor fault, if occurring during initialization.

Motor fault, if occurring during initialization.

Motor not running.

NextMove card faulty.

Command Timed Out

(Print Carriage)

This error reports that the print carriage has failed to move

to the demanded position within the time period. Possible

causes are:

Home sensor fault, if occurring during initialization.

Motor fault, if occurring during initialization.

Motor not running.

NextMove card faulty.

Command Timed Out

(Proflow)

This error reports that the proflow unit has failed to move to

the demanded position within the time period. Possible

causes are:

Home sensor fault, if occurring during initialization.

Motor fault, if occurring during initialization.

Motor not running.

NextMove card faulty.

Command Timed Out

(Rail System)

This error reports that the moving rail has failed to move to

the demanded position within the time period. Possible

causes are:

Home sensor fault, if occurring during initialization.

Motor fault, if occurring during initialization.

Motor not running.

NextMove card faulty.

Command Timed Out

(Screen Actuators)

This error reports that the actuator has failed to move to the

demanded position within the time period. Possible causes

are:

Home sensor fault, if occurring during initialization.

Motor fault, if occurring during initialization.

Motor not running.

NextMove card faulty.

Command Timed Out

(Front/Rear Squeegee)

This error reports that the front/rear squeegee has failed to

move to the demanded position within the time period.

Possible causes are:

Home sensor fault, if occurring during initialization.

Motor fault, if occurring during initialization.

Motor not running.

NextMove card faulty.

Downline Board Transfer

Fault

This error reports that the time the downline interface has

waited for a board has exceeded the time-out.

Downline Machine Not

Available

This error reports that the downline machine is unavailable

to accept the next board.

Event File Open Error This error reports that there was a problem opening the

event log backup file.

4.4 User Manual Software Version 6

ERROR MESSAGES

ERROR MESSAGE LISTING