N7201A616E00_0317.pdf - 第545页

NPM-W 2 EJM7DE-MB-07 O-00 7-1-1 -6 No. Item name Function when [ON] is selected 1 Force PCB Eject Ejects PCB forcibly even if there is no PCB requ est signal from the downstream mac hine. 2 Pre process other company M/C …

100%1 / 714
NPM-W2 EJM7DE-MB-07O-00
7-1-1-5
No. Item name Function when [ON] is selected
1
Nozzle 2D code
recog
Detects wrong nozzle setting and checks for proper orientation of nozzle on
the nozzle changer by recognizing the 2D code on the nozzle at the start of
automatic operation.
2
Can't use the Nzl
without 2D Code
Causes the machine to stop if nozzles without 2D code are mixed up.
3
2D code recognition
only when nozzle
exchange
Causestheheadcameratoskip2Dcoderecognitionofallnozzlessetinthenozzle
changerwhenrestartingthemachinethathasbeenstoppedduringproduction.
4
Temperature warning
check
Compares the current temperature of adhesive with the preset value on the
temperature control unit.
5
Inside changer auto
arrange
Rearranges the nozzles on the nozzle changer according to the data after
recognizing the nozzle 2D code.
6
Bad mark recognition
judge value is
variable
Uses the criterion value in the bad mark information to judge the bad mark
recognition for production boards.
7
Bad nozzle auto
change
If a certain nozzle is determined to be bad due to “Bad nozzle error rate”, this
option replaces the nozzle concerned with a normal one automatically. (12-
/16-nozzle heads)
8
Continue to product
when stuff detect
Allows production to be continued even after an error has occurred due to
detection of stuffed nozzle or filter.
9
Big nozzle manual
change (front side)
Enables the nozzles to be set manually without replacing them automatically.
10
Big nozzle manual
c
h
ange (rear side)
Enables the nozzles to be set manually without replacing them automatically.
No. Item name Function when [ON] is selected
1 Bad XY axis(front) Disables the front XY axis.
2 Bad XY axis(rear) Disables the front XY axis.
3
Time-lapse change
calibration during
producing of one
piece
Performs time-lapse change calibration during production of one PCB.
Setting information 4
● Default ：OFF
■ XY-axis
● Default ：OFF
■ Head
Unit
setting
Option setting 3
Operating procedure
7-1-1
NPM-W2 EJM7DE-MB-07O-00
7-1-1-6
No. Item name Function when [ON] is selected
1 Force PCB Eject
Ejects PCB forcibly even if there is no PCB request signal from the
downstream machine.
2
Pre process other
company M/C joint
Makes the timing of PCB request signal OFF from the downstream machine
earlier.
3
Pre process other
company M/C joint2
Hastens the timing of PCB request signal OFF from the downstream
machine.
4
All pattern bad board
pass
When all patterns are judged to be bad by bad mark recognition, this option
unloads the board to the downstream side without mounting parts on it.
5 F Proc. Eject Wait
When a third-party machine or conveyor is connected on the upstream side,
and “B. A. (Board Available) signal from it is received, PCB request signal is
sent to the upstream machine or conveyor, and a PCB is loaded.
6
Production item
name check
When this option is ON, the NPM machine checks the product name before a
PCB is loaded from the upstream machine. If the production data names do
not agree, the NPM comes to a single error stop.
7
Width adjustment
fixed
Disables width adjustment at any operation screen even during automatic
operation.
8
PCB connection
detect
Determines an error if two PCBs connected with onto each other are loaded.
9
PCB Y clamp
(option)
Keeps the Y clamp engaged also during mounting.
10
Conveyor width
check before
production
Checks that the conveyor width matches the setting in the production data
before starting production.
11
Positioning action
when overrun
Allows positioning to be performed again if a loaded PCB has overrun.
12
Multiple lot prevent
carrying (option)
Controls the board transfer during dual lane production so that the
subsequent lot will not overtake the lot ahead.
Setting information 5
● Default ：OFF
■ Conveyor
System
administration
NPM-W2 EJM7DE-MB-07O-00
7-1-1-7
No. Item name Function when [ON] is selected
1 Feeder maint warning
Displays a warning message when the shot count of tape feeder has
exceeded the warning value.
2
Part remainder number
warning
Displays a warning message when “Feeder remainder number warning
length” in “Action parameters” is reached.
3
Simple Remain
Manage
When the remainder of a reel used reaches 1, this option resets the
remainder, assuming that the reel has been used up.
4
Supply parts count
input when running
Allows the supply parts count for splicing to be input without stopping
production.
5 Splicing length stop
Causes the machine a single stop when the remaining reel is less than 1
200 mm (minimum length required for splicing).
6
Fdr parts collation
(option)
If tape feeders containing any parts different from those in the production
data downloaded to the machine are loaded, the interlock function of the
machine is activated, causing the machine to stop due to an error.
7
Unconditional parts
splicing
Enable parts to be re-verified when feeder parts verification is ON, even
though splicing verification has already been done.
8
Component splicing
executes when
remaining warning
happen
Enables splicing only for tape feeders with which a remainder warning has
occurred.
9 Feeder deploy free
Allows a tape feeder containing the same parts can be placed at any
desired slot before starting production or if parts empty has occurred. When
the specified feeder is used up, the arranged feeder is used automatically to
continue production.
10
Pick up sequence has
high priority when free
arrange
Gives priority to simultaneous pickup if it is involved when picking up parts
with “Feeder deploy free” ON. Notifies the operator that the cycle time may
be slower depending on the tape feeder arrangement.
Setting information 6
● Default ：OFF
■ Feeder
Unit
setting
Option setting 4
Operating procedure
7-1-1