YSM10安装调整(eng).pdf - 第64页
For Ser v ice E n gineer Service Information SI1610004E -000= YSM10_Proced ures for the adjustmen ts required after installing a machine 64/107 6.7 Before sta rting t he “ A C P - St ati on” adj ustment Startup the Cal…
For Service Engineer
Service Information
SI1610004E-000= YSM10_Procedures for the adjustments required after installing a machine
63/107
6.6.2 Change the “Board Size Height” to 10.0mm
Change the “Board Size Height” of the Board data “MCH_SETUP.ygx” before performing the
“ACP-Station” adjustment.
Board Size Height (mm): 1.6mm
10.0mm
:
The thickness of the station is 10.0mm. It is heavy with the air hose connected to it and may not be
secured properly just by the board clamp. (The station may tilt due to its own weight.)
Set the pushup pins under the 10.0mm thick part of the FAMF station in addition to the board clamp.
Figure 85
Change the setting
to “10.000”.
该文档是极速PDF编辑器生成，
如果想去掉该提示,请访问并下载：
http://www.jisupdfeditor.com/
For Service Engineer
Service Information
SI1610004E-000= YSM10_Procedures for the adjustments required after installing a machine
64/107
6.7 Before starting the “ACP-Station” adjustment
Startup the CalibSm adjustment utility
[027 ACP-Station] on the CalibSm main menu.
Figure 86
6.7.1 Setting for the items on the left side of the window
On the left side of the window, the settings for the table, the main camera, the camera to be
adjusted, and the s and the heads to be adjusted can be performed.
Figure 87
1. Check the setting of “Table” and “Lane”.
As YSM10 is equpped with only Table A and single lane, you do not need to change the setting.
2. Check the setting of the main camera.
The main (reference) component recognition camera for YSM10 is “3-Scan Main”.
3. Check the settings of the camera and the to be adjusted in the “Adj. Setting” area.
The adjustment can be performed consecutively by selecting all the s and the heads to be
adjusted.
When “5-Digital MultiC” is selected and the machine is equipped with two (2) multi cameras, tick
the “6-Digital MultiC” checkbox as well.
The s to be adjusted (“304(315)” and “307(318)”) are selected (the
checkboxes are ticked) referring to the head specification as default. Make sure that the correct
s are selected.
If the machine is equipped with an ANC
The s are changed automatically and the adjustment is performed consecutively.
If the machine is NOT equipped with an ANC
Attach the to the head to be adjusted by hand and perform the adjustment.
该文档是极速PDF编辑器生成，
如果想去掉该提示,请访问并下载：
http://www.jisupdfeditor.com/
For Service Engineer
Service Information
SI1610004E-000= YSM10_Procedures for the adjustments required after installing a machine
65/107
6.7.2 Setting for the items on the right side of the “AutoRun/Measure” window
On the right side of the “AutoRun/Measure” window, you can perform setting for each and
specify the “Mount No.” and the “Block No.”.
The s that can be adjusted with the machine are displayed in the “ Setting” pull-down
menu.
Figure 88
Other functions in “ Setting”
Item
Description
Default setting
Confirm Feedback
Basically, you do not need to tick the checkbox as whether to perform
feedback or not is automatically determined.
If you tick the checkbox, when the adjustment program judges that
the feedback needs to be performed, a message box appears asking
you whether to perform feedback or not.
Not ticked
Copy Precision for
MultiCam.
When the machine is equipped with two (2) cameras and the
ACP-Station adjustment is performed for the both cameras, the
checkbox is automatically ticked. The accuracy parameters obtained
by the adjustment for the first multi camera is copied to the other multi
camera, which will reduce the time for the adjustment.
Ticked
Reverse
When using the QFP with the white sticker on its back for
adjusting the Scan camera, tick the “Reverse” checkbox.
Not Ticked
Table 30
1. Select the to be used from “ Setting” pull-down menu.
The settings for more than one can be switched by selecting the s from the pull-down
menu. The “Speed”, the “Comp.No.”, the jig used for the adjustment ( QFP), and the
“StoragePos” items are set for each .
2. Check the setting of “Speed”.
The mounting speed for the adjustment can be set. “100” is normally selected.
3. Check the setting of “Comp.No.”.
Set the component to be mounted by the selected . Select the component number from the
board data (MCH_SETUP.ygx)
Part No.
Mark No.
QFP
304 (315)
11
29
QFP68
307 (318)
12
29
QFP208
Table 31
When performing the
adjustment with more than one
, switch the here
and perform the necessary
settings.
该文档是极速PDF编辑器生成，
如果想去掉该提示,请访问并下载：
http://www.jisupdfeditor.com/