00197042-04_SM_X-Serie-S_Customer_EN.pdf - 第10页
10 Service Manual SIPLACE X-Serie S 06/2019 Contents: 9.6.5 Replacing the control board .. 404 9.6.5.1 Control board SPS .. 405 9.6.6 Replacing the swivel head .. 406 9.6.7 Replacing the pneumatic cylinder .. 407…
9Service Manual SIPLACE X-Serie S 06/2019
Contents:
9.1.7 Replacing the articulated joint on the short-stroke cylinder.. 336
9.1.8 Replacing the short-stroke cylinder.. 339
9.1.9 Replacing the Cutter Blades.. 341
9.1.10 Replacing the wiper.. 346
9.1.11 Replacing Wiper Clip.. 348
9.1.12 Replacing the cutter cable.. 350
9.1.13 Replacing the throttle valve.. 351
9.1.13.1 Times for Setting the Throttle on the Cutter (From SW707.1).. 352
9.1.14 Replacing the solenoid valves.. 353
9.1.15 Replacing the silencer.. 354
9.2 COT insert.. 355
9.2.1 COT insert.. 355
9.2.2 Installation Positions of COT Insert and Manual Table (Table Positions).. 356
9.2.3 Replacing the COT Insert Assembly.. 356
9.2.4 Replacing the Feeder Control Unit (FCU).. 358
9.2.4.1 Feeder Control Unit (FCU).. 360
9.2.5 Replacing the 40-fold feeder unlock device.. 362
9.2.6 Replacing the unlocking pins.. 363
9.2.7 Replacing the safety switch.. 365
9.2.8 Replacing the empty tape duct assembly.. 366
9.2.9 Replacing the control valve.. 368
9.2.10 Replacing the empty tape duct Einsatz.. 369
9.2.11 Replacing the infeed control.. 371
9.3 X-Series Component Trolley.. 372
9.3.1 SIPLACE X-series component trolley.. 372
9.3.2 Replacing the Fixed/Guide Castors [00341918-xx].. 372
9.3.3 Replacing the locking latch.. 373
9.3.4 Replacing the Guide Profile/Entering Guide Feeder.. 375
9.3.5 Replacing the bearing assembly.. 376
9.3.6 Replacing the insert feeder.. 377
9.3.7 Replacing the Actuator/Protective Bracket.. 378
9.4 Docking Station for Component Trolley.. 379
9.4.1 Docking station for component trolley - overview.. 379
9.4.2 Replacing the power pack.. 381
9.4.3 Replacing the micro switch.. 382
9.4.4 Replacing the locking unit short-stroke cylinder.. 383
9.4.5 Replacing the locking lever.. 384
9.4.6 Replacing the positions end switch of the component trolley locking device.. 386
9.4.7 Replacing the 40-fold feeder unlocking device.. 387
9.4.8 Replacing the Feeder Control Unit (FCU).. 388
9.4.9 Replacing the Complete Coupling - Earthing and Compressed Air for the Bulk Case.. 391
9.4.10 Replacing the unlocking pushbutton.. 392
9.4.11 Replacing the control valve.. 394
9.5 Manual Table and JEDEC Tray Feeder.. 395
9.5.1 Manual table.. 395
9.5.2 SIPLACE JTF-S.. 396
9.5.3 Adapter.. 397
9.6 Smart Pin Support.. 398
9.6.1 Replacing the Pin Picker Assembly.. 399
9.6.2 Replacing the front section of the cylinder.. 400
9.6.3 Replacing the back section of the cylinder.. 402
9.6.4 Replacing the linear guide.. 403
10 Service Manual SIPLACE X-Serie S 06/2019
Contents:
9.6.5 Replacing the control board.. 404
9.6.5.1 Control board SPS.. 405
9.6.6 Replacing the swivel head.. 406
9.6.7 Replacing the pneumatic cylinder.. 407
9.6.8 Replacing the coil hose.. 408
9.6.9 Replacing the coiled cable.. 409
9.6.10 Replacing the Round Cable.. 411
9.6.11 Replacing the tension spring.. 412
9.6.12 Replacing the top sensor.. 413
9.6.13 Replacing the bottom sensor.. 414
9.6.14 Replacing the one-way restrictor.. 415
9.6.15 Replacing the solenoid valve.. 416
9.6.16 Replacing the solenoid valve cable.. 417
9.6.17 Replacing the press roller.. 418
9.6.18 Replacing the Magazine Recognition Board.. 419
9.6.18.1 Magazine recognition board.. 420
10 Vacuum Pump.. 421
10.1 Replacing the vacuum pump.. 421
10.2 Replacing the exhaust air hose.. 421
10.3 Replacing the connector unit box.. 422
10.4 Replacing the power supply cable for the vacuum pump.. 423
10.5 Replacing the suppressor module in the connector unit box.. 424
10.6 Replacing the circuit breaker in the connector box.. 425
10.7 Replacing the button in the connector unit box.. 425
10.8 Replacing the relay terminal block in the connector unit box.. 425
10.9 Replacing the diode terminal block in the connector unit box.. 425
1 Introduction
1.1 Safety instructions
Service Manual SIPLACE X-Serie S 06/2019 11
1 Introduction
This service guide is a manual or reference work for performing service work on the SIPLACE® X-
Series S placement machines.
For additional information, please also observe the instructions for the individual placement heads,
where necessary.
1.1 Safety instructions
DANGER
Nonobservance of these safety instructions may cause injury to personnel and dam-
age to the machine!
► Please observe the safety instructions in the user manual of the relevant machine
for all work!
1.1.1 Conventions for the use of safety instructions and symbols
Safety instructions
This manual contains notes that must be observed to guarantee your personal safety and to avoid
damage to equipment. These notes are highlighted by warning triangles and are indicated as fol-
lows according to the level of risk:
DANGER
Definition
For the purposes of this manual, this indicates that fatal or severe injuries or considerable
damage to property will occur if this hazard warning is not observed.
WARNING
Definition
For the purposes of this manual, this indicates that fatal or severe injuries or considerable
damage to equipment may occur if these warning instructions are not followed.
CAUTION
Definition
For the purposes of this manual, this indicates that minor injuries or damage to property
may occur if this caution is not observed.
NOTICE
Definition
For the purposes of this manual, this note provides information about the product or indic-
ates a part of the manual that requires particular attention.
Symbols
Example Description
Next This typeface marks controls and interface elements in the software.
► This symbol indicates actions that have to be performed by the operator.