00197042-04_SM_X-Serie-S_Customer_EN.pdf - 第121页
4 Electrics and control system 4.6 Replacing the monitor/monitor holder Service Manual SIPLACE X-Serie S 06/2019 121 4.6 Replacing the monitor/monitor holder Parts, equipment and tools ● Monitor SCD1520-TDC [03078913-xx]…
4 Electrics and control system
4.5 Indicator lamp
120 Service Manual SIPLACE X-Serie S 06/2019
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
Fig.144: Removing the indicator lamp
► Hold the base(1) of the indicator lamp
tightly, so that it does not rotate.
► Turn the top section of the indicator
lamp approx. 2cm anti-clockwise(2)
and then take the indicator lamp up and
off(3).
Installation
Fig.145: LED module with housing
Assembling the modules
► When assembling the modules, pay at-
tention to the line and arrow markings.
► First fit the modules together so that
the lines are on one another.
► Now turn the top modules approx. 2cm
clockwise, until the arrow is over the
line.
Hold the base tightly during this, so that
it does not turn.
4 Electrics and control system
4.6 Replacing the monitor/monitor holder
Service Manual SIPLACE X-Serie S 06/2019 121
4.6 Replacing the monitor/monitor holder
Parts, equipment and tools
●
Monitor SCD1520-TDC [03078913-xx]
●
Monitor holder [03042042‑xx]
●
Standard tooling
●
Torx screwdriver ESD 1.0-5.0 Nm [03078400-xx]
●
Bit holder for TorqueVario screwdriver [03078706-xx]
Overview
Fig.146: Overview of monitor
1. Monitor
2. Screws fastening the monitor holder to
the machine
3. Monitor connections
4. Screws fastening the monitor to its
holder
5. Screw (joint)
(torque 4.5Nm)
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Unplug all connections to the monitor. You may want to mark their positions, to make clear as-
signment easier later on.
► Loosen the upper and lower screws fastening the monitor bracket to the machine and lift the
monitor and its bracket out of the keyholes.
► Remove the four screws fastening the monitor to its bracket and then remove the monitor
bracket.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following
instructions:
– First tighten the screw (joint) with a torque of 4.5Nm.
4 Electrics and control system
4.7 Replacing the button
122 Service Manual SIPLACE X-Serie S 06/2019
4.7 Replacing the button
Parts, equipment and tools
Fig.147: Overview of button
1. Pushbutton
2. EMERGENCY STOP button
3. Twin pushbutton
Square shape Round shape
Pushbutton 00334095‑xx 03164001Sxx
EMERGENCY STOP button 00334073‑xx 03165966Sxx
Twin pushbutton 03084513‑xx 03170336Sxx
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Remove the relevant button. To do this, unplug all electrical connections. You might like to
mark their positions to make clear assignment easier later on.
Installation
► Follow the removal instructions in reverse order for installation.
4.8 Replacing the CAN switch
NOTICE
Only X-Series S up to No. Gxxxx
The CAN switch and the upgrade kit are only used in SIPLACE X-Series S machines up to
serial no. Gxxxx.
Parts, equipment and tools
●
CAN switch [03083844-xx] or
Upgrade kit PCB conveyor CAN switch X-Series S [03106370-xx]