00197042-04_SM_X-Serie-S_Customer_EN.pdf - 第43页
2 Basic Machine 2.8 Nozzle Changers and Reject Boxes Service Manual SIPLACE X-Serie S 06/2019 43 2.8 Nozzle Changers and Reject Boxes See also 2 9.2 "COT insert" [ } 355] 2.8.1 Nozzle Changers and Nozzle Stati…
2 Basic Machine
2.7 Replacing Stationary Component Camera Digital Type 25/33/36
42 Service Manual SIPLACE X-Serie S 06/2019
2.7.4 DIP Switch for Camera Types 25 and 33
Setting
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Remove the camera upper part and the cover on the lower part, to gain access to the DIP
switches.
► Set the DIP switches. (see below).
► Fit all parts by following the above instructions in the reverse order.
DIP switches
Boards with version status 01 and 02 are fitted with a TQ module. In this case, the DIP switching
block is 8 pin.
Boards with version status 03 or higher do not have a TQ module. In this case, the DIP switching
block is 6 pin.
Version state 01 and 02: DIP switch settings (8 pin)
S Setting for gantry* Comments
1 2
1 OFF OFF Bootstrap
2 OFF OFF Reset
3 OFF OFF Gantry ID 0
4 OFF ON Gantry ID 1
5 OFF OFF Test
6 OFF OFF CAN terminator
7 ON ON CAN speed: ON: 1 Mbit/s, OFF: 500 KB/s
8 x x x x OFF: FC camera (type 25), ON: IC camera (type
33)
* Not all gantries may be available, depending on the machine type.
Version state 03 and higher: DIP switch settings (6 pin)
S Setting for gantry* Comments
1 2
1 OFF OFF Reset
2 OFF OFF Gantry ID 0
3 OFF ON Gantry ID 1
4 x x x x LED: This switch is delivered with a fixed preset-
ting. Do not change this setting!
5 OFF OFF CAN terminator
6 x x x x OFF: FC camera (type 25), ON: IC camera (type
33)
* Not all gantries may be available, depending on the machine type.
See also
2 2.7.3.1 "Vision LED driver VLT 33" [}40]
2 Basic Machine
2.8 Nozzle Changers and Reject Boxes
Service Manual SIPLACE X-Serie S 06/2019 43
2.8 Nozzle Changers and Reject Boxes
See also
2 9.2 "COT insert" [}355]
2.8.1 Nozzle Changers and Nozzle Stations - Overview
Fig.31: Nozzle changer short [03103649‑xx]
Standard nozzle changer, short
[03103649‑xx] for four magazines
Fig.32: Nozzle changer, long [03147324‑xx]
Standard nozzle changer, long
[03147324‑xx] for six magazines
Fig.33: Nozzle changer, long
Nozzle changer, long
for SIPLACE C&P20 [03070123‑xx]
for SIPLACE C&P20M [03147324‑xx]
with six magazines [00119715‑xx]
Fig.34: Magazine 20xx [03066107-xx]
Magazine for nozzles of 20 xx series
Fig.35: Magazine 28xx [03065782-xx]
Magazine for nozzles of 28 xx series
2 Basic Machine
2.8 Nozzle Changers and Reject Boxes
44 Service Manual SIPLACE X-Serie S 06/2019
Fig.36: Magazine 40xx [03101503-xx]
Magazine for nozzles of 40 xx/60 xx series
Fig.37: Nozzle changer TwinStar (short) [03062452‑xx]
1. Nozzle changer TwinStar (short)
[03062452‑xx]
2. Magazine for 1 nozzle [03001807-xx]
3. Magazine for 2 nozzles [03005191-xx]
4. Nozzle changer in standard configura-
tion
1x magazine for 1 nozzle
3x magazine for 2 nozzles
2.8.2 Replacing the Nozzle Changer
NOTICE
Row two, MTC2, WPC
For more information about the row 2 nozzle changers and in combination with MTC2/
WPC, refer to the assembly instructions "NC row 2 - NC before MTC 2/
WPC" [DEEN:00197369‑xx].
Parts, equipment and tools
Select the relevant nozzle changers:
●
NC basic structure CPx/all assembly long [03147324–xx] (replaces [03103514‑xx]
[03070123‑xx])
●
NC CPx/all short [03147925‑xx] (replaces [03103649-xx] [03062463-xx])
●
Nozzle changer CPP X-Series [00119741-xx]
●
Nozzle changer C&P20 SX4/DX4 [00519851-xx]
●
Nozzle changer C&P20 SX1/SX2 [00519715-xx]
●
Nozzle changer Twin [03062452‑xx]
●
If required, NC shim plates [03021079-xx]
●
Depth measuring gauge (300mm) [03079617-xx]
●
Plastic plate
Overview
Fig.38: Nozzle changer with four 4xxx magazines
1. Four nozzle magazines
2. Four fastening screws
3. Four levers for removal of nozzle
magazines
4. Cover on the underside
The electronic and pneumatic compon-
ents are under the cover.