00197042-04_SM_X-Serie-S_Customer_EN.pdf - 第37页
2 Basic Machine 2.7 Replacing Stationary Component Camera Digital Type 25/33/36 Service Manual SIPLACE X-Serie S 06/2019 37 2.7 Replacing Stationary Component Camera Digital Type 25/33/36 Refer to the appropriate assembl…
2 Basic Machine
2.6 Replacing the machine foot
36 Service Manual SIPLACE X-Serie S 06/2019
2.6 Replacing the machine foot
DANGER
Heavy machine part
► The machine feet are very heavy. When screws are loosened, there is a risk that
these could fall down and crush limbs.
► When replacing the machine feet, you need to raise the machine slightly.
► Make sure that there is nobody in the hazard area. The unintentional movement or
lowering of the machine can create a risk of crushing limbs.
CAUTION
Do not move the machine
► Make sure that the machine is not moved and that the conveyor sides are not dam-
aged.
Parts, equipment and tools
Fig.25: Machine foot [03000890-xx] and machine foot HF [03002561-xx]
●
Machine foot [03000890-xx] or
Machine foot HF [03002561-xx]
●
Instruction manual for your machine
Removal/installation
► Please read the relevant chapter of the instruction manual:
– "Presetting the height of the middle machine feet"
– "Presetting the height of the outer machine feet"
See also
2 1.2 "Preparatory work..." [}16]
2 Basic Machine
2.7 Replacing Stationary Component Camera Digital Type 25/33/36
Service Manual SIPLACE X-Serie S 06/2019 37
2.7 Replacing Stationary Component Camera Digital Type
25/33/36
Refer to the appropriate assembly instructions:
●
Assembly instructions "SIPLACE X-Series S - Stationary Camera 25/33" [DE+EN: 00197397-xx]
●
Assembly instructions "SIPLACE X-Series S - Stationary Camera 25/33 GigE" [DE+EN:
00197710‑xx]
NOTICE
Subsequent installation or conversion of stationary cameras
Observe the following points, where necessary:
► "Incorrectly labeled spacers for stationary cameras" [DE: TI2014-02D04] [EN:
TI2014-02E04]
During retrofitting or conversion of stationary cameras or "Smart Pin Support Q10"
magazines, pay attention to correct fitting of the spacers.
► Assembly instructions "SIPLACE X-Series S - Smart Pin Support" [DE+EN:
00197394-xx]
NOTICE
Camera adaptor
You may need to fit an IC camera adaptor assembly (see assembly instructions).
► Location 1 to 3: IC camera adaptor assembly SX4a [03099054-xx]
► Location 4: IC camera adaptor assembly SP4 SX4a [03099004-xx]
Fig.26: Cables
From machine number Hxxxx, the stationary
cameras fitted will have GigE.
CAUTION!
Pay attention to the correct cabling of
the stationary cameras.
Never install a GigE camera in an
older machine (up to machine number
Gxxxx) with Hotlink interface as this
will result in destruction of the camera!
The Hotlink interface can be identified
by the orange cables.
The GigE interface can be identified by
the red cables.
.
See also
2 2.7.4 "DIP Switch for Camera Types 25 and 33" [}42]
2 Basic Machine
2.7 Replacing Stationary Component Camera Digital Type 25/33/36
38 Service Manual SIPLACE X-Serie S 06/2019
2.7.1 Installation Height of the Stationary Camera
CAUTION
Head crash danger
An incorrect installation height can result in a head crash!
The installation height at which the camera can be installed depends on the camera version. You
will either only be able to use one specific height or will have the option of several installation
heights. The following description only applies for the following camera versions with three possible
installation heights:
●
Stationary component camera P&P (type 33) 55x45 digit. [03016339-xx] from version -06
●
Stationary component camera P&P (type 36) 32x32 digit. [03042491-xx] from version -04
Stationary camera in position 1
Fig.27: Stationary camera in position 1
1. Screw
2. Thread in the machine frame
Position 1 has to be used in the following
cases:
●
SX1/SX2: always
●
SX4, X-Series: If at least one DLM or
CPP head is used in the corresponding
placement area.
Stationary camera in position 2
Position 2 is not relevant for the SX and the X-Series.
Stationary camera in position 3
Fig.28: Stationary camera in position 3
1. Screw
2. Thread in the machine frame
Position 3 has to be used in the following
cases:
●
SX1/SX2: never.
●
SX4, X-Series: If only TwinHeads are
used in the corresponding placement
area.