00197042-04_SM_X-Serie-S_Customer_EN.pdf - 第331页
9 Component feeding 9.1 Cutter Service Manual SIPLACE X-Serie S 06/2019 331 NOTICE The spring rings used to date are no longer permissible. The mount must therefore be changed. ► When fastening the new rail [03008869-03]…
9 Component feeding
9.1 Cutter
330 Service Manual SIPLACE X-Serie S 06/2019
Fig.423: COT insert (example of SIPLACEX4S shown)
► Remove the four screws(1) fastening
the cutter holder.
If there are also washers or serrated
lock washers present, these will need
to be used again in the same places
during installation.
► Carefully lower the cutter and lift it out
of the machine.
CAUTION
Additional work
► For all further work, either fix the cutter to the mounting plate with four hexagon
socket-head screws M6 or use screw clamps to fasten the cutter to a sturdy table.
► Do not place the cutter onto the pneumatic connections down on the lifting cylinders.
Installation
2
1
Fig.424: Cutter (using example of X-Series)
► Remove the two holders(1) from both
sides of the cutter, together with the
distance sleeves(2).
There may be washers or serrated lock
washers present. Mark their positions,
to make clear assignment easier later
on.
Fig.425: Fastening of new holder (example of
SIPLACEX4S shown)
1. 2x holder [03008869‑03]
2. 2x ISO4762-M4x16-A2-70
[03042507‑xx]
3. 4x serrated lock washers M4-
FST.1.4401 [03047857‑xx]
4. 2x ISO4762-M4x30-A2-70
[03042557‑xx]
To fit the holder, proceed as follows(1):
9 Component feeding
9.1 Cutter
Service Manual SIPLACE X-Serie S 06/2019 331
NOTICE
The spring rings used to date are no longer permissible. The mount must therefore
be changed.
► When fastening the new rail [03008869-03] use the four serrated lock washers M4-
FST.1.4401 [03047857-xx], instead of the four spring rings.
► Use the following screws to fasten the brackets:
2x ISO4762-M4x16-A2-70 [03042507-xx] and 2x ISO4762-M4x30-A2-70 [03042557-xx]
► If longer or shorter screws are used or if the serrated lock washers are missing, the
metal buffers will be subjected to excess strain and the screws could work loose. In
this case, the cutter fixtures are no longer reliable.
► Secure the screws with Loctite 243.
► Used screw clamps to protect the metal buffers from torsion during tightening.
► The maximum tightening torque is 2 Nm.
► Carefully lift the cutter onto the spacer sleeves. Use the spacer disks if provided.
► Tighten all four fastening screws.
1
3
2
Fig.426: Cutter (using example of X-Series)
CAUTION!
There is a risk of injuring yourself on
the cutting edge of the blades.
For this reason, the deflector plate (2),
cover plate (1) and protective sheet (3)
must be left mounted in place!
.
► Move the cutter into its installation position, using the support/chair for assistance.
► Carefully lift the cutter into the planned position.
► Tighten all four fastening screws.
► Reconnect to the electrical and compressed air systems.
► Fit the waste tape container.
► Follow the removal instructions in reverse order for further installation.
9 Component feeding
9.1 Cutter
332 Service Manual SIPLACE X-Serie S 06/2019
9.1.4 Replacing the Metal Buffer/Spacer Distance Piece
Parts
Fig.427: Spacer and metal buffer
03007432‑xx Spacer
00329209‑xx Metal buffer M4.65 Shore
Equipment and tools
00353832-xx Allen key set
Wire cutters
Cable ties
Overview
Fig.428: Metal buffer and spacer distance piece on cutter
1. Metal buffer and spacer (two on each
side)
The metal butters absorb the cutting vi-
bration to the machine base.