APPENDIX.pdf - 第10页

Samsung Component Placer CP-45F(V)/FS Operations Manual A-4 of arranged tape feeders and the number of feeders to be arranged are displayed.  <COMP> column Of the components used by the PCB being edited, tape feed…

100%1 / 76
Appendix A Optimizer
A-3
A.2. Setup Menu/Tape Feeder
Figure A-2. "Optimizer Setup: Tape Feeder" dialog box
The screen to set the optimum arrangement of tape feeder. The Optimizer can arrange
tape feeders in the optimum feeder lanes by considering simultaneous pickup and
operation time. But the user must specify the installation position for tray feeders and
stick feeders.
<FEED COMP> list box
In the left list box, the number of the feeder that is already arranged in the feeder lane
and each component name are displayed. For the front feeder base, F is attached in
front of the feeder lane number and for the rear feeder base, R is attached in front of
the feeder lane number. The feeders listed here are not arranged arbitrarily by the
Optimizer. However, the feeders already arranged affect other feeders when they are
arranged by the Optimizer. That is, when there are feeders already arranged, new
feeders are arranged to increase simultaneous pickup.
Among the feeders displayed here, move the feeders for which you want optimal
arrangement by the Optimizer to the right list box by clicking on the arrow button
(
) and execute the Optimizer.
<COMP # ARG AVL LIM> list box
In the right list box, the number of placement points for each component, the number
Samsung Component Placer CP-45F(V)/FS Operations Manual
A-4
of arranged tape feeders and the number of feeders to be arranged are displayed.
<COMP> column
Of the components used by the PCB being edited, tape feeder components are
displayed here.
<#> column
Displays the number of placement points for each component. You can refer to it
when you decide the number of feeders to arrange.
<ARG> column
Displays the number of feeders already arranged on the feeder lane for each
component. This number is the same with the number of feeder lanes in the left list
box.
<AVL> list box
Displays the number of feeders to be arranged by the Optimizer for each component.
<LIM> list box
Displays the sum of the feeders displayed in the <ARG> and <AVL> columns for
each component. In other words, it is the limit number of feeders that can be assigned
to each component. The minimum value is 1.
<Limit> button
Used to specify the number of feeders to be used for each component. If 1 feeder is
arranged for a component, entering 3 in this box and pressing the limit button makes
the number in the AVL column to 2. The Optimizer arranges up to 2 new feeders. Set
an appropriate number of feeders while considering the number of placement points
for each component. To get a better operation efficiency, allocate more feeders for the
components that have many placement points.
Arrow button(
)
Used to change the setting of an arranged feeder to the setting of a feeder to be
rearranged by the Optimizer.
<Remove Tape> button
Click on the <Remove Button> to ignore all the tape feeders already arranged and to
arrange new tape feeders. As this button is present at the bottom of the Optimizer
setting screen, it can be selected although the tape feeder setting tap is not displayed.
Appendix A Optimizer
A-5
A.3. Setup Menu/Nozzle
Figure A-3. "Optimizer Setup: Nozzle" dialog box
The screen to set the optimum arrangement of nozzles.
All the nozzles registered in the equipment are displayed in the <Arranged>, <Available>,
or <Prohibited> list box. The sum of nozzles in each list box is the same with the sum of
the heads (in the case of CP-45, it is 6). The user can set a desired number of nozzles to
be arranged by the Optimizer by adjusting the number of nozzles in the <Available> list
box.
<Nozzle> group/<Arranged> list box
The user can arrange nozzles in the ANC pocket directly in the ANC Setup Dialog
Box. The nozzles arranged in advance are displayed in the <Arranged> list box. The
nozzles listed here are used for operation but the Optimizer does not arrange them in
the pocket arbitrarily. To rearrange the nozzles already arranged by using the
Optimizer, select the desired nozzle and move it to the <Available> list box by
clicking on the arrow button (
). If the user wants to arrange the nozzle directly
again, the user needs to display the ANC Setup Dialog box and specify the pocket.
<Nozzle> group/<Available> list box
The list box to specify the nozzles to be arranged in the pocket by the Optimizer. In