APPENDIX.pdf - 第50页

Appendix B 3D Trouble Shooting Guide

B-27

Step Message

E - The left sensor of Hole Fix is not sensed.

Step1 - Press the STOP button. (Stop the buzzer sound).

Step2 - Open the equipment door.

Step3 - Check the size, position, and direction of the PCB.

Is the Hole Fixer inserted properly in the left Fix Hole?

. Yes, the Hole Fixer is inserted properly. Step4

. No, the Hole Fixer is not inserted properly. Step11

- Then click on the NEXT button.

Step4 - Adjust the position of the Sensor Dog.

- Then click on the NEXT button.

Step5 - Close the equipment door.

Step6 1. Press the RESET button.

2. Turn on the power for MOTOR.

3. Press the READY button.

- Then click on the NEXT button.

Step7 1. Select the HOME mode by using the MODE button in the teaching box.

2. Turn off all the LEDs by using the AXIS button.

3. Press the HOME START button.

-Then click on the NEXT button.

Step8 - Click on START or CONTINUE on MMI.

… 'START': starts operation with a new PCB.

Step9 - Click on START or CONTINUE on MMI.

Step10 - Press the START button to resume operation.

Step11 - Click on the BTU Down button in View->Manual Control of MMI.

- Then click on the NEXT button.

Step6 1. Remove the PCB after lowering the Backup Table.

2. Cancel the Hole Fixer.

3. Put the PCB.

4. Fit the Hole Fixer into the Fix Hole and secure it.

- Then click on the NEXT button. Step5

Error Code $3001 Link

Step Message

E - A PCB is in the input sensor area.

- Press START to continue operation.

- Click on Exit to end the TSG.

Error Code $3002 Link

Step Message

E - A PCB is in the waiting sensor area.

- Press START to continue operation.

- Click on Exit to end the TSG.

Error Code $3003 Link

Step Message

E - A PCB is in the mounting sensor area.

- Press START to continue operation.

- Click on Exit to end the TSG.

Samsung Component Placer CP-45F(V)/FS Operations Manual

B-28

Error Code $3004 Link

Step Message

E - A PCB is in the output sensor area.

- Press START to continue operation.

- Click on Exit to end the TSG.

Error Code $4300X Link

Step Message

E The X axis is sensed in the (-) S/W Limit by using the jog box.

Step1 - Press the STOP button. (Stop the buzzer sound).

Step2 - Move the X axis to a position in the S/W Limit by using the teaching box.

- Then click on the NEXT button.

Step3 - Check the setting from the Limits item in the System menu of MMI.

Stpe4 - Press the START button to resume operation.

Error Code $4300Y Link

Step Message

E The Y axis is sensed in the (-) S/W Limit by using the Jog Box.

Step1 - Press the STOP button. (Stop the buzzer sound).

Step2 - Move the Y axis to a position in the S/W Limit by using the teaching box.

- Then click on the NEXT button.

Step3 - Check the setting from the Limits item in the System menu of MMI.

Stpe4 - Press the START button to resume operation.

Error Code $4300Z Link

Step Message

E The Z axis is sensed in the (-) S/W Limit by using the Jog Box.

Step1 - Press the STOP button. (Stop the buzzer sound).

Step2 - Move the Z axis to a position in the S/W Limit by using the teaching box.

- Then click on the NEXT button.

Step3 - Check the setting from the Limits item in the System menu of MMI.

Stpe4 - Press the START button to resume operation.

Error Code $4301X Link

Step Message

E The X axis is sensed in the (+) S/W Limit by using the Jog box.

Step1 - Press the STOP button. (Stop the buzzer sound).

Step2 - Move the X axis to a position in the S/W Limit by using the teaching box.

- Then click on the NEXT button.

Step3 - Check the setting from the Limits item in the System menu of MMI.

Stpe4 - Press the START button to resume operation.

Error Code $4301Y Link

Step Message

E The Y axis is sensed in the (+) S/W Limit by using the Jog Box.

Step1 - Press the STOP button. (Stop the buzzer sound).

Step2 - Move the Y axis to a position in the S/W Limit by using the teaching box.

- Then click on the NEXT button.

Step3 - Check the setting from the Limits item in the System menu of MMI.

Appendix B 3D Trouble Shooting Guide

B-29

Stpe4 - Press the START button to resume operation.

Error Code $4301Z Link

Step Message

E The Z axis is sensed in the (+) S/W Limit by using the Jog Box.

Step1 - Press the STOP button. (Stop the buzzer sound).

Step2 - Move the Z axis to a position in the S/W Limit by using the teaching box.

- Then click on the NEXT button.

Step3 - Check the setting from the Limits item in the System menu of MMI.

Stpe4 - Press the START button to resume operation.

Error Code $5101 Link

Step Message

E - An error in the number of retries occurred at the Tape Feeder.

Step1 - Press the STOP button. (Stop the buzzer sound).

Step2 - Check if there are components in the corresponding feeder.

Step3 . Yes, there are components left. Step4

. No, there is no component left. Step11

- Then click on the NEXT button.

Step4 - Choose the current situation from above figure.

. (a) Pickup position error Step5

. (b) Vinyl cover is not completely taken off. Step6

. (c) Deviated pitch. Step7

. (d) Feeder error. Step8

. (e) Other. Step10

Step5

- Specify the component pickup position for the feeder again and resume

operation.

Step6 - Take off the vinyl and resume operation.

Step7 - Adjust the pitch and resume operation.

Step8 - Install the feeder securely.

- Then click on the NEXT button. Step9

Step9 - Press the START button to resume operation.

Step10 - Please contact Our C/S.

Step11 - Supply components and resume operation.

Error Code $5300 Link

Step Message

E - There is no component in the Tray feeder.

- Supply components and resume operation.

Error Code $5201 Link

Step Message

E - An error in the number of retries occurred at the Stick Feeder.

Step1 - Press the STOP button. (Stop the buzzer sound).

Step2 - Check if there are any components in the corresponding feeder.

. Yes, there are components left. Step3

. No, there is no component left.

- Then click on the NEXT button.

Step3 - Check the problem and choose one of the following items.

(a) X,Y position error. Step4