00195760-0102_UM_D3_SR605_EN.pdf - 第162页
3 Technical data for the machine User Manual SIPLACE D3 3.9 Feeder modules From software version SR.605.xx 07/2008 EN Edition 162 PLEASE NOTE – The waffle-p ack tray holder can only be set up at locations 2 and 4. – The …
User Manual SIPLACE D3 3 Technical data for the machine
From software version SR.605.xx 07/2008 EN Edition 3.9 Feeder modules
161
3.9.9.3 Assembly
3
Fig. 3.9 - 17 Installation
(1) Centering pins
(2) Magnetic rail
(3) Centering ball
(14), (15) This position must not be filled.
Positioning options Locations 2 and 4
Range of placement heads TH, C&P6, C&P12
Max. waffle-pack tray height
including components
C&P12
C&P6
TH
12.5 mm
12.5 mm
28.5 mm
3 Technical data for the machine User Manual SIPLACE D3
3.9 Feeder modules From software version SR.605.xx 07/2008 EN Edition
162
PLEASE NOTE
– The waffle-pack tray holder can only be set up at locations 2 and 4.
– The feeder module positions 14 and 15 on the component table must not be filled.
– The holder and the nozzle changer cannot be used at the same time at location 4.
– The component trolley cannot be docked in/out while the holder is fitted.
→ Insert the front side of the waffle-pack tray holder into the associated centering pin (A in Fig.
3.9 - 17
, page 161).
→ Then position the hole on the rear side of the waffle-pack tray holder onto the centering ball
on the component feeder table (B in Fig. 3.9 - 17
, page 161).
→ Make sure the waffle-pack tray is resting securely on the component table.
→ Position one side of the waffle-pack tray carrier in the mounting (C in Fig. 3.9 - 17
, page 161).
Then press the other side into the mounting (D in Fig. 3.9 - 17
, page 161).
→ Slide the waffle-pack tray up against the stop (E in Fig. 3.9 - 17
, page 161).
→ Secure the waffle-pack tray carrier by pressing the thrust pad (F in Fig. 3.9 - 17
, page 161)
downwards.
→ To remove the waffle-pack tray carrier, press the thrust pad once more.
PLEASE NOTE
Using the holder for small waffle-pack trays (136 mm) a waffle-pack tray (JEDEC or CENELEC
waffle-pack tray) can be fitted directly to the holder, in other words, without a waffle-pack tray car-
rier being used. However, the retainer will require changing (G in Fig. 3.9 - 17, page 161).
WARNING
All locations must be equipped with feeder modules in order to guarantee operational reliability.
If there are not enough feeder modules available, unassigned locations should be fitted with a
hand guard (dummy feeder module). When a waffle-pack holder is set up, the remaining loca-
tions have to be protected again with a hand guard.
User Manual SIPLACE D3 3 Technical data for the machine
From software version SR.605.xx 07/2008 EN Edition 3.9 Feeder modules
163
3.9.9.4 Changing the retainer
→ Hold the retainer (G in Fig. 3.9 - 17, page 161) firmly. Press the thrust pad downwards (F in
Fig. 3.9 - 17
, page 161) and remove the retainer by pressing it out sideways.
3.9.9.5 Data entry
→ Define the waffle-pack trays as described in the SIPLACE Pro operating instructions.
3.9.10 Dip module
Item no. 00117010-xx Dip module for flux and adhesives
3
Fig. 3.9 - 18 Dip module
(1) Dip module
(2) Rotating plate
(3) Squeegee