00195760-0102_UM_D3_SR605_EN.pdf - 第197页
User Manual SIPLACE D3 4 Setting up and commissioning From software version SR.605.xx 07/2008 EN Edition 4.3 Setting up the machine 197 4.3.4 Presetting the PCB conveyor height → Push the forks of the fork-lift under the…
4 Setting up and commissioning User Manual SIPLACE D3
4.3 Setting up the machine From software version SR.605.xx 07/2008 EN Edition
196
4.3.3 Tools and equipment
You will need the following tools and equipment to adjust the height of your machine:
– Fork wrench, size 36, item no. 00096286-01
Size 36 for the adjusting screw M24x2x120 to adjust the height of the machine feet 4
– Hook wrench 135 - 145 for adjusting the middle machine feet
Item no. 00376519-xx 4
– Single-ended spanner, size 65, item no. 00353827-01
Size 65 for the hexagon lock nut M24 on the middle machine foot 4
– Allen key, size 10, item no. 00373926-01
for hexagon socket head screws M12x80 for fixing the spacers for the middle machine feet4
– Allen key, size 19, item no. 00373928-01
for hexagon socket head screw M24x90 for clamping the four outer machine feet clamps4
– Fork-lift
Fork length: min. 1800 mm 4
Carrying power: min. 6000 kg 4
Width between forks: see Fig. 4.3 - 1
, page 197 4
– Spirit level: Accuracy 0.02 mm/m
– Air cushion transport system: SIPLACE HSxx, item no. 00119002-xx
User Manual SIPLACE D3 4 Setting up and commissioning
From software version SR.605.xx 07/2008 EN Edition 4.3 Setting up the machine
197
4.3.4 Presetting the PCB conveyor height
→ Push the forks of the fork-lift under the machine, as shown in Fig. 4.3 - 1.
4
Fig. 4.3 - 1 Contact surfaces - Forks parallel to the direction of PCB transport
(1) Contact surfaces for the forks of the fork-lift
WARNING 4
Please note the following points before you raise the machine in order to avoid irreversible dam-
age to the machine:
– Open the forks just wide enough to position them between the two machine feet (the attach-
ment points are shown in Fig. 4.3 - 1
). The machine feet are 776 mm apart. NEVER increase
the distance between the forks so that the machine is lifted on the side parts of the machine
frame, since this would deform the machine frame.
4 Setting up and commissioning User Manual SIPLACE D3
4.3 Setting up the machine From software version SR.605.xx 07/2008 EN Edition
198
→ Make sure that the forks are evenly loaded when you lift the machine. A firm support between
the forks and machine will prevent the machine tilting when it is raised. This will also prevent
a one-sided load on the machine feet, which would deform the fixing of the machine feet. We
recommend that a second person watch the machine as it is raised, and make sure that the
machine does not tip to one side when lifted with the fork-lift.
→ With the fork-lift, raise the machine approximately 35 cm. This will avoid any risk of injuring
your feet if you lower the machine feet accidentally.
The machine stands on 6 feet.
– 4 outer machine feet (item 1 in Fig. 4.3 - 3
, page 199)
There are two versions of the outer machine feet: 4
– outer machine foot for the PCB conveyor height of 830 mm, length 369 mm,
item no. 03041008-01 (item 1 in Fig. 4.3 - 2
)
– outer machine foot for the PCB conveyor heights of 900, 930 and 950 mm, length
439 mm, item no. 03000890-02 (item 2 in Fig. 4.3 - 2
)
– 2 middle machine feet (item 2 in Fig. 4.3 - 3
, page 199) with 2 spacers (item 3 and item 4 in
Fig. 4.3 - 3
, page 199) for adjusting the height, if necessary.
4
Fig. 4.3 - 2 Outer machine feet - two versions (dimensions in millimeters)