MEC-CP842-1.0E.pdf - 第105页
Maintenance >> Lubrication MEC-CP842-1.0E 5-45 5.2.21 Lubricating the Rotary Holder Positioning Pins The arrow in the diagram i ndicates the lubrication point. Apply grease with the positioning pin pushed in. C746M…
Maintenance >> Lubrication
5-44 MEC-CP842-1.0E
5.2.20 Lubricating the Cam Lever Air Cylinder
Procedure
1 Open the lid of the lubricator with a blade screwdriver.
2 Lower the lubricator cover.
3 Visually check the oil level of the oil tank and slowly pour in the oil to the lubri-
cator. Do not to exceed the upper limit while pouring in the oil.
Note: The maximum amount of oil that can be supplied to the lubricator is 75 cc. If the oil level does
not reach the tip of the pipe inside the case, there will be insufficient oil to lubricate the cylin-
der.
4 Replace the lubricator cover and attach the oil inlet cap.
5 Check and discard of any waste oil in the collection bottle.
C746M3T18
52
Turbine oil + NASKALUBE (*) Every 6 months
Lubrication points
Schedule
Types of lubricant
Air cylinder
(*) This lubricant is a unique blend of oil (Turbine oil + NASKALUBE) available only
from Fuji.
A
A
B
B
C746M3037
Cam lever air cylinder
(52)
Case
Cover
Bottle
Lubricator
Lid
Upper limit
Pipe
Lower limit
Maintenance >> Lubrication
MEC-CP842-1.0E 5-45
5.2.21 Lubricating the Rotary Holder Positioning
Pins
The arrow in the diagram indicates the lubrication point. Apply grease with the
positioning pin pushed in.
C746M3T22E
.WDTKECVKQPRQKPVU
53
AFC grease /QPVJN[
5EJGFWNG
6[RGUQHNWDTKECPV
4QVCT[JQNFGTRQUKVKQPKPIRKP
5RGEKCNPQ\\NG
(KVVKPI
6WDG
5[TKPIG
%QPPGEVVJGU[TKPIG(S2184A), tube (DGPJ6000), fitting (WPJ1261),
and NY-axis special nozzle to apply grease.
C84PHD003E
2WUJKPVJGRQUKVKQPKPIRKP
YJGPCRRN[KPIITGCUG
Maintenance >> Lubrication
5-46 MEC-CP842-1.0E
5.2.22 Lubrication Checklist
C746M3T19
(1/2)
Daphne Exponex No. 2
Every 3 months
Monthly
Every 3 months
Every 3 months
Monthly
Every 3 months
Monthly
Every 6 months
Every 6 months
Every 6 months
Every 3 months
Every 3 months
Monthly
Monthly
Monthly
Monthly
Monthly
Monthly
Monthly
Every 3 months
Every 3 months
Every 3 months
Monthly
Weekly
Weekly
Monthly
Monthly
Monthly
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Multemp LRL3
Daphne Exponex No. 2
Multemp LRL3
Daphne Exponex No. 2
Daphne Super Multi Oil 32
Multemp SRL
Daphne Exponex No. 2
Daphne Exponex No. 2
Daphne Exponex No. 2
Daphne Exponex No. 2
Daphne Exponex No. 2
AFC grease
AFC grease
Daphne Exponex No. 2
Daphne Exponex No. 2
AFC grease
Daphne Exponex No. 2
AFC grease
Daphne Exponex No. 2
Daphne Exponex No. 2
Daphne Exponex No. 2
Daphne Exponex No. 2
AFC grease
AFC grease
Multemp LRL3
X-axis LM block
X-axis ball screw
X-axis screw cover
Y-axis LM block
Y-axis ball screw
Y-axis screw cover
Z-axis ball screw
Ball screw
Lifter guide bar
LM block
LM rail
Cam follower
Tape feed lever
Shaft
Joint
Cam
Cam lever pivot (7 points)
Cam lever bearing
NZ-axis ball screw
NZ-axis LM rail
NZ-axis holder
NZ-axis LM block
-axis connecting pin
Movable cutter
Cam follower
Thrust bearing
LM block
Rolle
Daphne Exponex No. 2
Daphne Exponex No. 2
Lubrication points
Schedule
Check
Types of lubricant
XY-table
Conveyors
Carriers
Tape advance
link
Cam box
NY-axis pickup
offset
Waste tape
disposal