3OM-1751-002w_G5S.pdf - 第257页
3OM-1751 2-89 1303-001 4.2 "Line Cong." T ab Sheet [3] [1] [2] [6] [7] [8] [9] Moving Cells [4] [5] F3B80 [1] # of Mc The number of machines in the line is set in this text box. [2] Line Operation System The o…
3OM-1751
2-88
[7] Fdr. Alt. Info. Dsp. mode
All feeder
When selected, the machine information is displayed whenever the
"Alternate" operation is performed.
Last feeder
When selected, the machine information is displayed only when the
"Alternate" operation is performed where only one "Alternate" available
feeder is left.
[8] Altn. Comp. ID List
Whether or not the alternative component list is to be used, is set in this data
box.
When the alternative component list is to be used, the alternative component
is compared in the pattern program check in the pattern program change
operation and whether or not the alternative component can be used, is
checked.
Altn. Comp. ID List Setting
The alternative component list reference procedure is specied in this data
box.
Common
: When selected, the list of the alternative components
common to the product models, is used.
Pattern Program
: When selected, the list of the alterative components set
for each product model, is used.
[9] Operator #2 ope level
When selected, the window is changed to one specially for Operator 2.
Normal
: When selected, the normal window is displayed.
Easy
: When selected, the window is changed to a special main window
for production start, stop and component reload, etc., where the
number of operation buttons is less than those on the normal
window.
[10] Panel lock mode
The panel lock mode is setup in this data box.
[11] Automatic cover lock
The automatic cover lock at the time of the cover open/close, is setup in this
data box.
1303-001
4.1 "General" Tab Sheet
3OM-1751
2-891303-001
4.2 "Line Cong." Tab Sheet
[3]
[1]
[2]
[6]
[7] [8] [9]
Moving Cells
[4]
[5]
F3B80
[1] # of Mc
The number of machines in the line is set in this text box.
[2] Line Operation System
The operation system in the line is selected from the following items and
setup.
Std
: Usually, this is selected.
LISA
: When the NA02001 LISA System Software SIGMA Series (Option)
is purchased and used, this is selected.
[3] PCB Transfer LAN I/F
Whether or not the LAN is to be used, is set up in this data box.
Enable
: When selected, LAN is enabled.
Disable
: When selected, LAN is disabled.
[4] Remote Control
"Enable" or "Disable" is set for the remote control operation from a machine
in the line.
Enable
: When selected, the remote control is enabled.
Disable
: When selected, the remote control (line start, etc.) is disabled from
a machine in the line.
Note
The PCB discharge operation, etc., is enabled.
4.2 "Line Cong." Tab Sheet
Graphic
Development
3OM-1751
2-901303-001
[5] Line Machine Data Display Section
Displayed is the data of line machine.
Mc Name
The machine name or IP address is set in this data box.
Mc Type
The machine type is selected in this selection box.
Input, Output
Whether the input machine and output machine are the associated machines
(SIGMA series) or non-associated machines, is selected in this selection box.
Sel
The machine to be re-arranged is selected in this selection box.
[6] [Send to Line] Button
When this button is pressed, the line conguration setup data is sent to the
machines in the line.
[7] Rearrangement Button
When this button is pressed, the machine arrangement order is changed.
After selecting the moving cell for the subject machine, re-arrange the
machine location using the [
] or [ ] button.
[8] [Conrm] Button
When this button is pressed, the machine selected in "[4] Line Machine Data
Display Section" is conrmed. When pressed, the tower lamp is turned ON
in the selected machine and buzzer sounds.
[9] [Application] Button
Using this button, the entered value is applied.
[Cancel] Button
When this button is pressed, the input data is cancelled and the saved data is
returned.
4.2 "Line Cong." Tab Sheet