80S-20贴片机.pdf - 第349页

SIPLACE 80S-20/F4 Service Manual 11 Control Unit Edition 03/97 11.2 Set-Up Configuration of M44 Computer (Machine Controller) 11 - 7 1 1.2 Set-Up Confi guration of M44 Computer (Machin e Controller) ● Swit ch off the ma …

100%1 / 483
11 Control Unit SIPLACE 80S-20/F4 Service Manual
11.1 Replacing Modules Edition 03/97
11 - 6
11.1.5 Replacing the Hard Disk / Floppy Disk Board
Spare parts
Floppy/winchester AMS-M349-A100, from item no. 00319704-01
● Disconnect all plug-in connections on the front panel of the machine controller (plugs x3, x4 sa, x5 sa; see
Fig. 11.1.2).
● Unscrew and remove the MC board front panel mounting screws (2 slotted-head screws) and the hard disk /
floppy disk board mounting screws (4 slotted-head screws).
NOTE
The MC and hard disk / floppy disk boards are connected together by two short cables.
● Carefully pull out the MC and hard disk / floppy disk boards. Place the boards on an ESD-checked surface.
● Disconnect the connecting cables between the boards (see the section Replacing Computer M44).
● Insert the new hard disk / floppy disk board into the MC board.
● To fit the boards proceed in the reverse sequence of operations.
NOTE
When inserting the connecting plugs make sure you have the correct slots on the front panel. Should you have
lost the setup data for the M44 see Section 11.2.
● Switch the machine on and install the current station software (see Adjustment instructions) .
● Copy the original MA data from the backup copy onto the hard disk.
SIPLACE 80S-20/F4 Service Manual 11 Control Unit
Edition 03/97 11.2 Set-Up Configuration of M44 Computer (Machine Controller)
11 - 7
11.2 Set-Up Configuration of M44 Computer (Machine
Controller)
● Switch off the machine.
● Switch the monitor to the M44 computer on the multiplexer. (Switch setting: 4 for M44, see Fig. 11.2.1).
Fig. 11.2.1 Multiplexer above control unit
● Unplug the keyboard from the station computer and plug it into the machine controller (the socket is next to
the station computer).
● Switch on the machine and press the keys
Ctrl - Alt - Ins (Strg - Alt - Einfg) when you are requested to do
so.
NOTE
To change the data you will need to use the numerical keypad. This is included in a normal keyboard. The
keys are marked with violet numbers and characters in their top left corner (for example, keys 7-0, U-P, J-
ö, and so on).
Press the Fn key to activate the numerical keypad function of the individual keys.
● Switch the monitor to automatic mode on the multiplexer (switch setting: 1 see Fig. 11.2.1).
11.2.1 Configuration Data
11.2.1.1 Screen 1
Date: tt. mmm jjjj
Time: hh:mm:ss
Drive A: 1.44, 3 ½ in.
Drive B: None
Video: EGA / VGA
1
2
3
4
11 Control Unit SIPLACE 80S-20/F4 Service Manual
11.2 Set-Up Configuration of M44 Computer (Machine Controller) Edition 03/97
11 - 8
Post message: Maximize
Quick boot: Disable
Halt on: ALL errors
Security: Disable
Virus Warury: Disable
Booting sequence: A, C
Default speed: High
Disk 0 49 (automatic hard disk detection)
Disk 1 None
11.2.1.2 Screen 2
> Bios < Enabled D000: Disabled E000: Disabled
> Video < Enabled D400: Disabled E400: Disabled
Disabled D800: Disabled E800: Disabled
Disabled DC00: Disabled EC00: Disabled
External cache: Enabled Default speed: High
Internal cache: Enabled Slow setting: Fast
COM A: 3F8h
COM B: 2F8h Console rediv: Enable / ANSI
LPT: 378h
Floppy drive: Enabled
IDE: Enabled
11.2.1.3 Screen 3
I/O selection RAM window SMP memory window SMP COM1/2: Disabled
Start address 0000H Start address 0000 00H SMP COM3/4: Disabled
End address 0000H End address 0000 FFH SMP LPT 2: Disabled