80S-20贴片机.pdf - 第463页
14 Pneumatic Cutter Service Manual SIPLACE 80S- 20/F4/F5 14.1 Pneumatic Cutter and Empty-Tape Duct Edition 04/98 14 - 5 14.1.4 Overview: Pneumatic Cutte r with Empty-Tape Duct Fig. 14.1.1 Overview of Pneumatic Cutter and…
Service Manual SIPLACE 80S-20/F4/F5 14 Pneumatic Cutter
Edition 04/98 14.1 Pneumatic Cutter and Empty-Tape Duct
14 - 4
14.1.2 Spare Parts
NOTE
The movable blade, the stationary blade and the holddowns (on left and right: see Fig. 14.1.5) are
DWWXQHG
to
one another and must therefore always be
H[FKDQJHGDVDVHW
The empty-tape duct is
QRW
part of the “pneumatic cutter”.
The cutter remains installed while the spare parts listed below are being installed !
Quantity Designation: Item No.: Note:
- 1 Cutter assembly 00328647-01 for empty tapes 15 mm high
- 1 Set of spacers 00095472-01
- 1 Empty-tape duct assembly (= long) 00332779-01 for changeover table area
- 1 Empty-tape duct assembly (= short) 00335102-01 for changeover table area
(next to WPC)
- 1 Blade, stationary 00328732-01 See above note
- 1 Blade, movable 00328738-01 See above note
- 1 Spacer 00328730-01 Total of 2 (see above note)
- 1 Rubber-metal vibration damper 00333878-01 2 each on left and right
- 1 (Solenoid) valve ass’y 00330930-01 1 each on left and right
- 1 Short-stroke cylinder 00328976-01 1 each on left and right
- 1 Articulated joint (complete) 00330928-01 1 each on left and right
- 1 Proximity switch right (front/back) 00332899-01 2 each on left and right
with cable tape cutter
- 1 Proximity switch left (front/back) 00332900-01 2 each on left and right)
with cable tape cutter
- 1 Cable: Control board tape, cutter- valve 00332901-01 1 per valve
- 1 Control board tape cutter S50 00329699-01 for F4, F5, S-20, HS-50
- 1 One-way restrictor 00319619-01 2 per cylinder on left and right
- 1 Cover (for control board) 00340658-01 1 alltogether
14.1.3 Tools, Expendable Materials, Documentation
● Set of socket wrenches
● Slotted screwdriver, size 4
● Open-end wrenches, width across flats 10 and 14
● Cross-slotted screwdriver, size 1
● Loctite no. 243, item no. 00334892-01 (for assembly of articulated joint and blade/strip)
● Loctite no. 454, item no. 00318541-01 (for one-way restrictors)
● Water-insoluble marker
● Operating manual for SITEST program, Version 404.xxx, English, item no. 00191147-01
14 Pneumatic Cutter Service Manual SIPLACE 80S-20/F4/F5
14.1 Pneumatic Cutter and Empty-Tape Duct Edition 04/98
14 - 5
14.1.4 Overview: Pneumatic Cutter with Empty-Tape Duct
Fig. 14.1.1 Overview of Pneumatic Cutter and Empty-Tape Duct
Key:
1) "Pneumatic cutter"
2) 3) 4) Retaining bracket for cutter, left and right, including fastening bolts*)
5) Nuts and bolts to fasten the cutter on the retaining brackets,
2 socket hex bolts each, M 6x10
2 hex nuts each, M6
6) 7) Baffle including fastening bolts (is not dismantled).
8) Empty-tape duct (dismantle or exchange only as a single unit)
9) Fasteners for the empty-tape ducts:
2 socket hex bolts M 4 x 6
10) Pins (left and right) and spacers underneath
*) Undo these bolts only to install the replacement cutter (see WARNING in Section 14.1.1).
Service Manual SIPLACE 80S-20/F4/F5 14 Pneumatic Cutter
Edition 04/98 14.1 Pneumatic Cutter and Empty-Tape Duct
14 - 6
14.1.5 Diagram of Pneumatic System
Fig. 14.1.2 Diagram of Pneumatic System