444CEOM1-CM202.pdf - 第107页
Page 3-9 FUNCTIONS 3 444C-E-OMA03-A01-05 Production Settings 3-2-5 Feeder Arrangement Y ou can check which chip is on which feeder address. First, check the state of the feeders arranged on the stage. • The information o…
Page 3-8
444C-E-OMA03-A01-01
Production Settings
3-2-4 Board Transport
This is used to perform transporting board in, transferring it from the stage A to B and transporting
it out to the next process for each step.
• The board on the conveyor is displayed as a green rectangle. While it is being transported, its
image is blinking.
∗ After pressing PCB transfer on the production settings menu, make sure the servo switch is ON,
and then press
UNLOCK
→
START
.
CM202
[Stage A]
UNLOCK
+ Carry in
Transports the board in from the previous
process to the left conveyor on the stage A.
UNLOCK
+ Load
Transports the board from the left conveyor to
the right conveyor on the stage A.
[Stage B]
UNLOCK
+ Carry in
Transports the board from the right conveyor
on the stage A to the left conveyor on the stage
B.
UNLOCK
+ Load
Transports the board from the left conveyor to
the right conveyor on the stage B.
UNLOCK
+ Carry out
Transports the board from the right conveyor
on the stage B out to the next process.
CM201
UNLOCK
+ Carry in
Transports the board in from the previous
process to the left conveyor.
UNLOCK
+ Load
Transports the board from the left conveyor to
the right conveyor.
UNLOCK
+ Unload & Carry out
Transports the board from the right conveyor
out to the next process.
444C-EOp-PcPt-002
Page 3-9
FUNCTIONS
3
444C-E-OMA03-A01-05
Production Settings
3-2-5 Feeder Arrangement
You can check which chip is on which feeder address.
First, check the state of the feeders arranged on the stage.
• The information of the chips on each feeder is displayed in the order of feeder address. Through
the state of occupancy, you can see which feeder address on the feeder table is used at a glance.
The number of the residual chips on each reel is also displayed.
• Select the feeder table you will check.
(CM201 has only the stage A.)
Draws out the selected feeder table. Pressing
the switch again returns the feeder table where
it was.
Reset
Resets the number of the residual chips
pointed by a cursor now. (Pressing ↑ and ↓
moves a cursor up and down.)
All reset
Resets the number of the residual chips on all
the feeders. When the message appears, press
Yes .
Call by Adrs
Pressing this switch displays the input screen.
When you enter an address and press ENT ,
a cursor moves to the specified address.
∗ When the remaining chip count is “0”, a yellow
mark lights up in this field. Check the feeder
and replace the workpieces. Pressing Reset
will reset the remaining count and delete the
yellow lit.
L feeder Table
out
R feeder Table
out
∗ For CM201-DS or CM202-DS, the feeder table
draw-out function is an option.
Page 3-10
444C-E-OMA03-A01-02
Production Settings
Occupancy
Occupancy
Pressing this switch displays the screen as
shown left.
The state of physical occupancy of table is
displayed.
(CM201 has the table No. 1 and 2 only.)
Comprehensive parts information
Complete part info
Pressing this switch displays the screen as
shown left.
The comprehensive information of parts
including the chip information of the feeder
pointed by a cursor is displayed.
∗ Move a cursor to the address you would like
to display, then press this switch.
Angle definition
Angle
definition
Pressing this switch displays the screen as
shown left.
The angle definition of the main chips in picking
up and mounting is displayed.