444CEOM1-CM202.pdf - 第117页
Page 3-19 FUNCTIONS 3 3-4-4 Nozzle Changing (Option) This is used to change the nozzle attached to the optional head for the one in the nozzle changer (option). ∗ This is not displayed when the nozzle changer (option) ha…
Page 3-18
3-4-2 Conveyor Width Adjustment
This is used to adjust the widths of all the conveyors to the set size of board automatically.
∗ Make sure no board is on the conveyor beforehand.
∗ After you have pressed Cnvr adjustment on the machine adjustment menu, make sure the servo
switches are ON, and then press
UNLOCK
→
START
. The conveyor width adjustment screen is dis-
played.
Choose a stage.
Press this switch to adjust the width to the
board width of production data.
When you would like to set the optional board
width, enter it with numeric keys.
Press
UNLOCK
+ Run .
The rails are adjusted automatically.
3-4-3 Board Transport
This is used to perform transporting board in, transferring it from the stage A to B and transporting
it out to the next process for each step.
∗ After you have pressed PCB transfer on the machine adjustment menu, make sure the servo
switches are ON, and then press
UNLOCK
→
START
. The board transport screen is displayed.
∗ The operating method is the same as that of the board transport of production settings.
( 3-2-4 Board Transport)
Machine Adjustment
1
2
3
444C-E-OMA03-A01-02
M35E
TURN OFF THE SERVO SWITCH BEFORE PLACING A BOARD ON OR
REMOVING IT FROM THE CONVEYOR.
You will have serious injury if the machine is actuated.
WARNING
Page 3-19
FUNCTIONS
3
3-4-4 Nozzle Changing (Option)
This is used to change the nozzle attached to the optional head for the one in the nozzle changer
(option).
∗ This is not displayed when the nozzle changer (option) has not been set.
Choose a target head.
(CM201 has only the stage A.)
Choose a nozzle attached to the head.
Choose a nozzle in the changer.
Pressing
UNLOCK
+ Nozzle set fits the nozzle in
the nozzle changer to the head.
Pressing
UNLOCK
+ Nozl set chk removes a
nozzle from the head and puts it away in the
nozzle changer.
3-4-5 Pick-up and Mounting Motions
This is used to check the pick-up, recognition and mounting position of the chosen head or nozzle.
Choose a target head.
(CM201 has only the stage A.)
Choose a head or a nozzle.
For the nozzles that support the simultaneous
pick-up, you can choose the two of them at the
same time. (Each combination such as POS1
and POS2, POS3 and POS4, POS5 and
POS6.)
Press
UNLOCK
+ Each position key.
The chosen head or nozzle moves to that
position.
In the Pick up field, set the address and type.
In the Mount field, choose the X-Y coordinates.
• At the pick-up position, letting the nozzle out/
back, rising/lowering Z-axis and letting the
sending rod out/back can be performed.
Machine Adjustment
1
2
3
4
1
2
3
444C-E-OMA03-A01-04
Page 3-20
Machine Adjustment
3-4-6 Input Check
All the input addresses the machine uses are sampled every other second, and its state is dis-
played in bit.
List display
Display for each address
• Select the stage to be displayed.
• The states of the input addresses the machine
uses are displayed with names for each bit.
Highlighted name shows its bit is ON (1).
(When you press the “Name” button, the state
of that bit is checked and displayed again.
Call by No
Displays the address that includes the speci-
fied No. at the left side of screen.
444C-E-OMA03-A01-02
Address List