00194474-0702_AI_HeadReconfig_X_605_DE+EN.pdf - 第205页

Head Reconfiguration Kits 2 Assemb ly Instructions - SIPLACE X-Series Head Reconfiguration Kits 07/2010 Edition 205 2.12.4.2 Machine serial number =< B325 and IC camera, versio n >= FS04 (FC camera >= FS03) : Mo…

100%1 / 276
2 Assembly Instructions - SIPLACE X-Series Head Reconfiguration Kits Head Reconfiguration Kits
07/2010 Edition
204
: Then carefully place the body of the camera on the supporting frame.
: Screw it firmly onto the supporting frame (3 bolts).
2.12.4 Setting the DIP switches on the vision control unit for the TwinHead
Mixing of different camera types (< FS04 / ≥ FS04) is not recommended and is also not
described in this chapter.
2.12.4.1 Machine serial number >= B326 and IC camera version >= FS04 (FC camera >= FS03)
From B326 the "CO camera, stat. P&P (TYPE33) 55x45 digit." (item no. 03016339-) ≤ 04 is
required. This camera does not require a vision control unit.
2
See Chapter 2.15, ”Circuit diagrams” from machine serial number B326
2
2
2
2
2
Head Reconfiguration Kits 2 Assembly Instructions - SIPLACE X-Series Head Reconfiguration Kits
07/2010 Edition
205
2.12.4.2 Machine serial number =< B325 and IC camera, version >= FS04 (FC camera >=
FS03)
: Mount "Control unit 1 Vision stationary" (item no. 00363961-) in the appropriate slot.
The vision control unit for placement area 1 is located in the main distributor (location 4). 2
The vision control unit for placement area 2 is located in the main distributor (location 2). 2
: Unplug the CAN bus cable (X2) on the "Control unit 1 Vision stationary" (item no. 00363961-)
if present.
: Remove the existing TQM module on the vision control unit if present.
2
CAUTION: Faults can subsequently occur on the CAN bus otherwise.
The CAN bus cable must be insulated with an adhesive tape and fixed to a wiring harness to
avoid malfunctions.
2
: Plug the "adapter cable for power cameras" (item no. 03059912-01) between the X4 or X5
"Control unit 1 Vision stationary" (item no. 00363961-) and the black cable.
See Chapter 2.15 ”Circuit diagrams” up to machine serial no. B325 (observe comments). 2
2
SUB 2
MAIN 2
Vision control unit without a CAN bus
and without a TQM module 2
2 Assembly Instructions - SIPLACE X-Series Head Reconfiguration Kits Head Reconfiguration Kits
07/2010 Edition
206
: Changeover the DIP switch on the "Control unit 1, vision stationary" (item no. 00363961-) :
– for a sub-distributor (SD): 5 and 6 to ON, the others to OFF. 2
– for a main distributor (MD): 6 to ON, the others to OFF. 2
2.12.4.3 Machine serial number =< B325 and IC camera version < FS04 (FC camera < FS03)
TQM167 SIPLACE Embedded module" item no. 03003536- to the "Control unit 1 Vision station-
ary" (item no. 00363961-) is required. This TQM module may need to be ordered separately. 2
: Mount "Control unit 1 Vision stationary" (item no. 00363961-) in the appropriate slot.
– The vision control unit for placement area 1 is located in the main distributor (location 4).
– The vision control unit for placement area 2 is located in the main distributor (location 2).
: Plug the TQM module on the board "Control unit 1 Vision stationary" (item no. 00363961-).
2
CAUTION: After power up of the machine, also check the BIOS and application version of the
vision and perform a download, if necessary.
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2