182050 User manual.pdf - 第225页
semi automatic &21680$ %/(5( 3/(1,6+0 (176 %/8(81' (56&5 ((1& /($1(5 Software Version 07SP02 User Manual 8.17 22. T oggle the screen clamp to th e up position ( OFF ) (standard chase onl y). 23. Remov…
semi automatic
&21680$%/(5(3/(1,6+0(176
%/8(81'(56&5((1&/($1(5
8.16 User Manual Software Version 07SP02
11. If the set preference is set to pause, the following window is displayed:
12. Select Defer (F8). The print run continues.
13. Select End Run (F1).
14. Go to Step 17.
15. If the set preference is set to suspend, the following window is displayed:
16. Select End Run (F8).
17. Press Open Cover (F2).
18. If the paper roll is to be replenished continue with Step 19. If the solvent
tank only is to be replenished go to Step 20.
19. Press Change Screen (F2).
20. Raise the printhead cover.
21. If the paper roll is to be replenished continue with Step 22. If the solvent
tank only is to be replenished go to Solvent Replenishment section.
Pause on Warning
Cleaner Solvent Low. Please refill.
Defer
End
Run
Stop
Cycle
Suspend on Warning
Cleaner Solvent Low. Please refill.
End
Run
Run
Open
Cover
Paste
Load
Clean
Screen
Setup Monitor Maint.
Change
Screen
Board
Clamps
Prime
Paper
Prime
Solvent
Exit
semi automatic
&21680$%/(5(3/(1,6+0(176
%/8(81'(56&5((1&/($1(5
Software Version 07SP02 User Manual 8.17
22. Toggle the screen clamp to the up position (OFF) (standard chase only).
23. Remove the stencil from the machine.
24. Go to Paper Replenishment section.
Solvent Replenishment
WARNING
RECOMMENDED SOLVENTS. ANY SOLVENTS USED MUST COMPLY WITH
LOCAL ENVIRONMENTAL GUIDELINES. DEK RECOMMEND USING SOLVENTS
THAT ARE ENVIRONMENTALLLY FRIENDLY, IE CFC FREE AND WATER BASED.
SOLVENTS USED MUST HAVE FAST EVAPORATION RATES AND FLASHPOINT
SPECIFICATIONS GREATER THAN 39ºC.
WARNING
SOLDER PASTE AND SOLVENTS. WHEN USING OR HANDLING ANY SOLDER
PASTE OR SOLVENT FORMULATION THE MANUFACTURERS’ RECOMMEND
SAFETY PRECAUTIONS MUST BE STRICTLY ADHERED TO.
WARNING
PROTECTIVE CLOTHING. APPROVED PROTECTIVE CLOTHING SHOULD BE
WORN BY SOLDER PASTE AND SOLVENT HANDLERS AT ALL TIMES TO
ELIMINATE FUME INHALATION, EYE CONTACT, SKIN CONTACT AND
INGESTION.
WARNING
SOLVENT SOLUTION. DO NOT MIX SOLVENT SOLUTIONS. FLUSH THE
SOLVENT TANK THOROUGHLY WHEN CHANGING TO A DIFFERENT SOLVENT
SOLUTION.
semi automatic
&21680$%/(5(3/(1,6+0(176
%/8(81'(56&5((1&/($1(5
8.18 User Manual Software Version 07SP02
WARNING
SOLVENT SPRAY. THE UNDERSCREEN CLEANER SPRAYS A FINE JET OF
SOLVENT SOLUTION ON TO THE CLEANER. APPROVED PROTECTIVE
CLOTHING SHOULD BE WORN.
1. Remove the solvent tank cap (1) from the solvent tank (2).
2. Using a suitable container refill the tank and replace the cap.
3. Lower the printhead cover.
4. Press the System button.
5. Press Prime Solvent (F6).
The message ‘Press the two button control buttons to prime solvent.’
is displayed.
6. Prime the solvent using the two button control.
7. Press Exit (F8).
Paper Replenishment
WARNING
PROTECTIVE CLOTHING. APPROVED PROTECTIVE CLOTHING SHOULD BE
WORN BY SOLDER PASTE AND SOLVENT HANDLERS AT ALL TIMES TO
ELIMINATE FUME INHALATION, EYE CONTACT, SKIN CONTACT AND
INGESTION.
WARNING
FLAMMABLE. THE USED PAPER ROLL CONTAINS RESIDUES OF
UNDERSCREEN CLEANER FLUID AND SOLDER PASTE. OBSERVE
MANUFACTURERS’ RECOMMENDED DISPOSAL INSTRUCTIONS.
1
2
Change
Screen
Board
Clamps
Prime
Paper
Prime
Solvent
Exit
Change
Screen
Board
Clamps
Prime
Paper
Prime
Solvent
Exit