182050 User manual.pdf - 第81页
semi automatic 0$&+,1 (352*5 $00,1 * 67$*( 35,17 ,1581 02'( Software Version 07SP02 User Manual 1.71 10. Repeat S teps 8 and 9 for the other deflec tor . 1 1. Lower the printhead cover . 12. Press the …
semi automatic
0$&+,1(352*5$00,1*
67$*(35,17,158102'(
1.70 User Manual Software Version 07SP02
STAGE 11 - PRINT IN RUN MODE
1. Select Setup (F6).
2. Select Mode (F1) until Auto is indicated in the mode option on the monitor.
3. Select Exit (F8).
4. Place the board onto the rails.
5. Select Run (F1). If squeegees are being used continue with Step 6, if
ProFlow is being used go to Step 21.
6. During the first print stroke, when the squeegee is down printing on the
board, select Stop Cycle (F2). The print cycle stops and the printer lid bolt
releases allowing access to the print carriage.
7. Raise the printhead cover.
8. Release the screws holding one paste deflector allowing it to drop into
contact with the stencil.
9. Insert a 0.25mm feeler between the deflector and the stencil. Tighten the
screws checking that the 0.25mm gap remains.
Run
Open
Cover
Paste
Load
Clean
Screen
Setup Monitor Maint.
Mode
Load
Data
Edit
Data
Setup
Squeegee
Change
Screen
Change
Tooling
Change
Language
Exit
Mode
Load
Data
Edit
Data
Setup
Squeegee
Change
Screen
Change
Tooling
Change
Language
Exit
Run
Open
Cover
Paste
Load
Clean
Screen
Setup Monitor Maint.
End
Run
Stop
Cycle
semi automatic
0$&+,1(352*5$00,1*
67$*(35,17,158102'(
Software Version 07SP02 User Manual 1.71
10. Repeat Steps 8 and 9 for the other deflector.
11. Lower the printhead cover.
12. Press the System button.
13. Select Continue (F1).
14. After the squeegee has moved approximately 20mm, select Stop Cycle
(F2).
15. Raise the printhead cover.
16. Check the deflectors are not touching the stencil.
17. Lower the printhead cover.
18. Press the System button.
19. Select Continue (F1).
20. Repeat Steps 6-19 for the other squeegee.
21. The printer operates continuously. The menu bar displays the following
options, these may be selected at any time during a print run:
End Run Selecting this option stops the printer on completion of the current print cycle.
Stop Cycle Selecting this option stops the printer immediately, halting all actions.
Continue
End
Run
Stop
Cycle
Continue
End
Run
Stop
Cycle
semi automatic
0$&+,1(352*5$00,1*
0(183$5$0(7(56
1.72 User Manual Software Version 07SP02
MENU PARAMETERS
Each product has a set of parameters which are unique to that particular product
and which need to be setup to obtain acceptable printing results. These
parameters are listed below with a definition of each as an aid to machine setup.
Product Name The file name for the particular product. The name can consist of up to eight
alphanumeric characters with no punctuation.
Product ID The product ID is a parameter that allows a description of the product. This
string may be up to 32 characters long, but only the first 20 characters are
displayed.
Image Detail This parameter allows the user to modify the stencil image data of the selected
screen library file. Once selected, pressing Incr. or Decr. Keys opens the Image
Detail Configuration page.
NOTE
This parameter is only displayed, if Screen Size in Set Preferences has been
selected to Screen Library.
Mesh Front This parameter sets the distance between the inner edge of the stencil frame
and the stencil glue line at the front of the frame. It defines the area that should
not be contacted by the squeegees/ProFlow.
Mesh Rear This parameter sets the distance between the inner edge of the stencil frame
and the stencil glue line at the rear of the frame. It defines the area that should
not be contacted by the squeegees/ProFlow.
Mesh Left This parameter sets the distance between the inner edge of the stencil frame
and the stencil glue line at the left of the frame. It defines the area that should
not be contacted by the squeegees/ProFlow.
Mesh Right This parameter sets the distance between the inner edge of the stencil frame
and the stencil glue line at the right of the frame. It defines the area that should
not be contacted by the squeegees/ProFlow.
Minimum Maximum Increment Default
0.0mm Screen Length - 250.0mm 0.1mm 38.0mm
Minimum Maximum Increment Default
0.0mm Screen Length - 250.0mm 0.1mm 38.0mm
Minimum Maximum Increment Default
0.0mm Screen Width - 250.0mm 0.1mm 38.0mm
Minimum Maximum Increment Default
0.0mm Screen Width - 250.0mm 0.1mm 38.0mm