00197463-03_SM_CPP_Customer_EN.pdf - 第32页
4 Component camera and component sensor 4.2 Replacing the component sensor [03037106-xx] 32 Service Manual SIPLACE Multistar (CPP / CPP M) 02/2018 4.2 Replacing the component sensor [03037106-xx] Parts, equipment and too…
4 Component camera and component sensor
4.1 Replacing the component camera [03018637‑xx]
Service Manual SIPLACE Multistar (CPP / CPP M) 02/2018 31
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following in-
structions:
CAUTION
Installation instructions
► Make sure that you do not damage or contaminate the camera lens system.
► Tighten the fourscrews fastening the component camera base with a torque of 2Nm
and the other two screws hand-tight.
► Make sure that the GigE cable is run correctly (see below).
Fig.31: Fastening the GigE cable
Only heads with GigE:
► Use cable ties to fasten the GigE cable to the fix-
ture(1) (if present).
4 Component camera and component sensor
4.2 Replacing the component sensor [03037106-xx]
32 Service Manual SIPLACE Multistar (CPP / CPP M) 02/2018
4.2 Replacing the component sensor [03037106-xx]
Parts, equipment and tools
●
CPP component sensor [03037106-xx]
Overview
Fig.32: BE sensor
1. Fastening screws for component sensor
2. Connector
3. Component sensor
As a default, each CPP head is fitted with a compo-
nent sensor in the pickup/place position.
The component sensor monitors the presence and/or
component height after pickup and before placement.
Preparation
► Remove the head from the machine. For details about removing and fitting the placement
head, refer to the service manual for your machine.
fit the head on the head mount [03056231‑xx].
Removal
CAUTION
Prisms on the component sensor
Take care not to damage the component sensor prisms.
► Unplug the connector from the component sensor by pressing the sides of it together slightly.
This releases the catch in the connector.
► Remove the two fastening screws.
► Carefully pull the connector off.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following in-
structions:
CAUTION
Installation instructions
► Tighten the screws fastening the component sensor with a torque of 1.45Nm.
► To place components smaller than 0201, you need to calibrate the component sensor.
For more information, read section 10.3 "Calibrating the CO Sensor" [}117].
4 Component camera and component sensor
4.3 Replacing the component sensor cable [03063595-xx]
Service Manual SIPLACE Multistar (CPP / CPP M) 02/2018 33
4.3 Replacing the component sensor cable [03063595-xx]
Parts, equipment and tools
●
Component sensor CPP [03063595‑xx]
Overview
Fig.33: Component sensor cable
1. Plug for intermediate distributor2 (ID2)
2. Intermediate distributor 2 with KE control board
ID2 (rucksack board)
See also 9.2 "Replacing Intermediate Distributors
1 and 2" [}107]
3. Cable to component sensor
4. Connector on component sensor
Preparation
► Remove the head from the machine. For details about removing and fitting the placement
head, refer to the service manual for your machine.
fit the head on the head mount [03056231‑xx].
► Make sure that the component sensor protective cap is fitted.
1.1.3 "Protecting the component sensor" [}8]
Removal
► Unplug the connector from the component sensor by pressing the sides of it together slightly.
This releases the catch in the connector.
► Using the same procedure, unplug the connector (X21) from ID2.
► Remove all relevant cable ties. You may want to mark their positions for easier exact replace-
ment later on.
► Remove the cable.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following in-
structions:
CAUTION
Installation instructions
► Fasten the cable with cable ties.
► Make sure that the cable is run correctly.