00197463-03_SM_CPP_Customer_EN.pdf - 第53页
5 Front plate, star, Z axis and smoothed distributor disc 5.5 Replacing the Single Core Solution (SCS)[03054790Sxx] (only for heads fromFS05) Service Manual SIPLACE Multistar (CPP / CPP M) 02/2018 53 5.5 Replacing the S…
5 Front plate, star, Z axis and smoothed distributor disc
5.4 Removing the valve terminal (only for heads from FS05 upwards)
52 Service Manual SIPLACE Multistar (CPP / CPP M) 02/2018
Fig.75: Fastening the valve terminal
1. The old valve terminal [03082217‑xx] is fixed with
six screws to the heads up to and including
FS04.
2. The new valve terminal [03115167‑xx] is fixed
with five screws to the heads up to number [KL-
J5-0162] .
3. The new valve terminal [03115167‑xx] is fixed
with six screws to heads from number [KL-
J5-0162].
► Fasten the valve terminal with the screws
provided.
Tighten the screws crosswise with a torque of
0.17 +/- 0.03Nm.
Fig.76: Flexprint cable
1. Connector closed
2. Connector open
3. Flexprint removed
► Insert the Flexprint cable as far as the stop into
the connector and lock the connector.
► Follow the removal instructions in reverse order for further installation.
Also observe the installation instructions in the following sections:
5.6 "Replacing the energy transmission for the rotor [03068843‑xx]" [}63]
5.2 "Removing and fitting the star (only for heads from FS05 upwards)" [}43]
5.1 "Replacing the front plate [03061102-xx]" [}35]
► Observe in particular the torques specified!
5 Front plate, star, Z axis and smoothed distributor disc
5.5 Replacing the Single Core Solution (SCS)[03054790Sxx] (only for heads fromFS05)
Service Manual SIPLACE Multistar (CPP / CPP M) 02/2018 53
5.5 Replacing the Single Core Solution (SCS)[03054790Sxx]
(only for heads fromFS05)
Parts, equipment and tools
●
SCS assembly CPP [03054790Sxx]
Overview
Fig.77: Star structure
1. Energy transmission for rotor
2. Valve terminal
3. Star carrier with DP drives
4. Single Core Solution (SCS).
5. Holding circuit with screwed joint
Fig.78: SCS
The SCS consists of two boards, the power and the
control module.
See also:
5.5.1 "Power module for 12 DP drives
[03054771‑xx]" [}58]
5.5.2 "Control module for 12 DP drives
[03054784‑xx]" [}60]
NOTICE!
Heads up to FS04
The SCS is not replaced in heads up to and in-
cluding FS04.
.
Preparation
► Remove the head from the machine. For details about removing and fitting the placement
head, refer to the service manual for your machine.
fit the head on the head mount [03056231‑xx].
► Make sure that the component sensor protective cap is fitted.
1.1.3 "Protecting the component sensor" [}8]
5 Front plate, star, Z axis and smoothed distributor disc
5.5 Replacing the Single Core Solution (SCS)[03054790Sxx] (only for heads fromFS05)
54 Service Manual SIPLACE Multistar (CPP / CPP M) 02/2018
Removal
► If required, dismantle the front plate.
5.1 "Replacing the front plate [03061102-xx]" [}35]
► Remove the star.
5.2 "Removing and fitting the star (only for heads from FS05 upwards)" [}43]
► Remove the holding circuit.
8.4 "Replacing the holding circuit" [}101]
Fig.79: Removing the fastening screws for the connector
► For all twelve DP drives: remove both screws (1),
which fasten the connector to the Flexprint cables
on the SCS.
Fig.80: Removing the strain relief
► Remove the screw on the strain relief for the
Flexprint cable and remove the cover plate.
Fig.81: Removing the Flexprint cable
► Open the connector (1) on the Flexprint cable.
► Remove the Flexprint cable(2).
► Remove the white support(3).